(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. H

    4050 JD tractor

    I'm gaining oil in the crankcase. Why? Is it hyd. oil or fuel? The tractor was just split because the PTO clutch needed replaced. Thanks for your time & knowledge.
  2. S

    Massey Ferguson 255 Aux hydr. not working

    Looking at buying a MF 255 from aging uncle at very decent price. The auxilary pump is either not working, or won't engage. The lever in photo 1 will only move about an inch, and doesn't engage anything. This is my first tractor purchase, and I know nothing about this MF. My uncle said he never...
  3. C

    gasket sealer?

    I am in the process of rebuilding the geared part of the transmission in my cotton picker. It has shafts with gears that the end play is controlled with thin metal shims of various thickness stacked together under bearing caps. My question is what type of sealer would be good to use to keep...
  4. M

    Ford 3000 hydraulic lift

    The lift quit working on my daughter's 3000 and the transmission oil is white (assuming it has water in it) The oil in the hydraulic pump is dark and the rear axle oil is low. I am going to change both, however I am not clear as to which supplies the lift. Can anyone tell me which source of oil...
  5. R

    6 to 12 volt on Farmall H

    I want to change my H from 6 to 12 volt where can I find the wiring information and resistor to put on the system. or would it be better to change the coil to 12 volt.
  6. 2

    Overhaul

    Looking for somebody in Michigan to overhaul 2-53. Want to get some HP. Any suggestions?
  7. 7

    timing

    What is the correct timing degrees for a 706 Gas 263 engine? And at what RPM?
  8. A

    2510 serial number

    Thanks to MARK-IA, I found the serial number but now don't know what it means as to the year. I'm new to the John Deere tractors, although I have 6 tractors, this is my first John Deere. Thanks for any help. The serial number is SNT711R005137R
  9. K

    Does your state belong to National Pedal Pull?

    Thats one mean looking dude on the left in the pic. Is he the security force from B and S? lol
  10. H

    R.P.M.

    what is the rpm on a jub pto.thanksdoes it change acording to gear you are in and also in netural. thanks
  11. K

    Turbo

    Is it a direct injected engine or the old powercell type? As far as a 301 case 6 cyl they never made one. Unless you are talking about the 301 IH engine and they will turbo just fine. If it is a case 6 cyl they will turbo ok. Some just work out alot better than others as far as performance.
  12. K

    Grandby pull and tornado

    Hey Larry im sure glad i left when i did. I tried to call Richard on his cell to warn you guys. Sure glad to hear everyone is ok. King Case
  13. K

    MM GVI light front axle

    Camm Machine and Welding 812 347 2040.
  14. K

    Southwest Missouri Shoal Creek pulling club schedule

    The ones at the Granby track are April 19th 3pm May 10th 3pm June 14th 6pm July 12th 4pm picnic 6pm pull Sept 14th 1pm Oct 12th 1pm. They also have two others at other locations. Aug 16th Sheldon MO after the parade. Sept ? didnt get that date down. Its at the Richards farm in Arma KS. Hope this...
  15. K

    Southwest Missouri Shoal Creek pulling club schedule

    I will try to get it today and post it tonight.
  16. K

    case 870 for tractorpulling

    What type of class are you wanting to pull? A std trans is best if you are going really high hp. A power shift will up to 250hp in a 1070 with only some torque limiter work. My uncle had a 1070 powershift around 265hp pulled it 8 years then sold it. The people still pulled it and the powershift...
  17. K

    Wichita Pulllling Sled

    This is my thoughts on the sled. My tractor runs as close to 3mph that if i open it 100% off the start it will sound the horn. I dont have to go but 70feet and i can open it up fully. I have never been DQed by his sled and have pulled it alot. So im saying i never had a problem or actually have...
  18. K

    Wichita Pulllling Sled

    What im saying is at our club he has been more than fair with his price. As far as what goes on at Whihita i dont know the facts. But im guessing he's not getting the full 25 per hook all to himself right. I can say this i wont be there. Its a NATPA pull and i wont go to them. King Case
  19. K

    Wichita Pulllling Sled

    I have pulled Larrys sled for several years and personaly have never had a problem with him or the sled. Yes there are nicer sleds out there. But for what Larry charges your not going to get the latest and greatest sled built. He has always been more than fair with our club. King Case
  20. K

    M W 9 speed parts needed for a M.

    Im in need of some parts for a M with a mw setup. Anyone out there have any or know where a man might get something for one? thanks
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top