(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. E

    350B Dozer VS Backhoe

    Ive got a 350B Dozer that I use around the ranch mainly pushing up brush piles and dragging cut down dead trees around. I'm thinking a Backhoe could do the same work as the dozer plus I could put a thumb on it and use it to load logs into the dump truck to haul to brush piles. currently I cut...
  2. E

    JD 350B Front Crossbar Removal

    I would like to remove my front crossbar to repair the wallowed out holes. How big of a job and how long for an average wrench to get it out. Thanks Engine One Eight
  3. E

    JD 350B Starting Electrical Issue

    Problem Solved It was the "firewall" connector. Connections were full of dirt and rusty. A little contact cleaner and we were back in business.
  4. E

    JD 350B Starting Electrical Issue

    More info for JD. The engine wont turn over at all or will turn over barely. I'm jump starting it with jumper cables off my service truck or another tractor. The cables appear to be original. I'm going to get it into my shop soon as I just discovered I had two broken bolts on the front...
  5. E

    JD 350B Starting Electrical Issue

    My 350B Dozer doesnt want to start. Acts like a dead battery. I had the starter rebuilt by a reliable shop in Tulsa, Put a new battery in and you still have to jump start it. When you jump it she starts right up immediately, usually on the first crank. The negative cable is grounded to the...
  6. E

    79 C60 swap 350 to 366

    I have a C60 with a tired 350. I pulled a 366 out of a wrecked truck. Will the bellhousing off the 350 work? Any changes in motor mounts, crossmembers etc? If I decide to just rebuild the 350 should I use my core (truck engine) or will any 350 suffice? The truck is used to haul brush in...
  7. E

    1974 C60 door hinges and hood springs

    Have you tried Heavy Chevy truck parts or LMC truck parts? They seem to be the source for reproduced pick up parts. I have used LMC for interior parts and was very happy with their service. If you need used stuff give me a call, I salvage 2 ton chevy trucks in NE Oklahoma
  8. E

    JD Weight Question

    I have a set of JD cast rear wheel weights with D2628R cast into them. They are NOT pancake style like on my 2510. What do they fit? thanks John
  9. E

    2510 Seat Questions

    Just purchased a 2510 and the seat cover is gone as well as most of the foam. This has resulted in the back rusting out so recovering the seat is not an option. Can anyone recommend a good replacement. Has anyone priced this item from Deere? Thanks Engine One Eight
  10. E

    Dirt/Gravel hauling business with 2 Ton Truck

    Need some numbers. Thinking of starting a part time business hauling gravel and dirt with a 2 ton chevy dump truck. I live within 3 miles of gravel pit and limestone pit and would be hauling local (25 miles) hauls. What should I expect to pay for insurance. How do I figure repair expense for...
  11. E

    IH 444 Remote Hydraulic Valve Question

    Yes, I"m sure the barrel or cylinder of the valve has a crack in it. You can see the oil coming out. Looks like the plug that screws into the bottom may have been turned once too many times. E18
  12. E

    IH 444 Remote Hydraulic Valve Question

    The hydraulic valve on my IH 444 is cracked and leaking oil. This is the valve under and to the side of the seat that controls oil flow for hydraulic cylinders. What other IH tractors shared the same valve and would be likely donors?
  13. E

    4010 Propane Value

    Looking at a 4010 Propane synchro range, wide front, complete 3 point, well used condition, good tires,runs and works. Thinking of doing some trading with the owner and would like to know if this is a rare item or run of the mill. He's asking around 5,000.00 Thanks E18
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top