(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. R

    woods belly mower on an 8N

    Thanks for the info and the link. I did exactly as you said, tightened till they were tight together.
  2. R

    woods belly mower on an 8N

    It is a taper lock bushing. My thought was, If I turned the bushing down a little, when I tighten the two together it wouldnt crack again. I have not measured anything yet so I dont know what I would take off. Why would it fit so tight that it breaks? The bushing has relief cuts in it to allow...
  3. R

    woods belly mower on an 8N

    Was your cracked thru the key way also? If so did you weld the inside of it? I tought of turning maybe .005 off the bushing so that it wouldnt crack again. What do you think?
  4. R

    woods belly mower on an 8N

    The sheave from one Woods dealer was 350.00. I believe we will try the welding first and see what happens. Thanks for you input. Bob
  5. R

    woods belly mower on an 8N

    I wont use it cracked, The crack is just by the keyway. With the bushing out, the crack closes up tight. The outside where the belt runs is not cracked.
  6. R

    woods belly mower on an 8N

    I have a woods belly mower (L59 I believe). I was putting the sheave onto the PTO and while tightining it to the bushing, the sheave cracked along the key way. I think this is made out of cast iron. Would it be safe to have it welded? Does anyone have one they may want to sell?
  7. R

    1950 8N brakes

    I Have not had it apart but do want to get it fixed. The brake will lock up from time to time while you are moving if you happen to touch the pedal accidentally. It dont take much movement in the pedal to have this happen. I have a belly mower that I will be putting on and mowing 3 acres. I dont...
  8. R

    1950 8N brakes

    I have not done any kind of adjusting yet and these brakes are the ones that was on it when I bought the tractor so I dont know how old they are. I dont know if they have been champered or not. Do you do this to old brakes or new, or both?
  9. R

    1950 8N brakes

    What would cause a brake to lock up? The right brake will lock up if you touch the pedal sometimes. If you step on it a couple times or reach down and pull up on it, then it is fine. It does not do it every time. You can also put it in reverse for a foot or two and that also releases it. The...
  10. R

    Snow plow mounting pictures

    CJ, do you know anything about the blade? Who made it?
  11. R

    8N with front blade

    Thanks to oldhokie and the brkt he made. It work really good
  12. R

    Hydraulic pump for snow blade for 8N

    I am using a cable that runs under the tractor and lifts from the drawbar.
  13. R

    8N with no power ( update )

    I am running the tractor with the main adjustment needle in and it works fine now. here is a picture of the ( main jet?? ) that the main adjustment needle seated on. Looks like part number 9N9533. This is what was taken out. After your replies,I took a better look at the manual and I dont see...
  14. R

    8N with no power ( update )

    Found a problem today, Small needle under the nozzle in the carb. Took it out and now it runs fine. The FO4 manual shows it in there but a fried who works on carbs didnt know why it was needed. For some reason this would allow you to remove the main adjustment needle from the carb and the...
  15. R

    Northwest Oh.

    North of Columbus? I live close to Van Wert.
  16. R

    Northwest Oh.

    Anyone on here from Northwest Ohio?
  17. R

    8N front snow plow. What do I look for?

    I bought a front blade amonth ago for 150.00. I seen one on Ebay today for 450.00 I think it was, dont remember where it was. The one I bought bolts under the rearend and the front axle pin. Lifts with the 3 point.
  18. R

    8N with no power ( update )

    No, I wasnt trying to do that. I have a front dozer blade on it and it dont move if I was to hit somthing. This is the first time using the blade.
  19. R

    8N with no power ( update )

    Ok, Checked the wires and they were good. Checked the point gap and was a little small so I adjusted them. Checked gas flow coming out of the carb, Looked good to me, I dont know how it should be but I would say it was coming out as strong as it is from the gas line. This helped as I was able to...
  20. R

    8N with no power

    I have a 1950 8N, side distributor and have no power. New points, plugs, wires, condensor, rotor, cap, insulator and copper strap in the distributor. New float needle and gaskets in the carb. I cleaned the carb filter and sediment bowl. I have good gas flow to the carb and good clean gas. The...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top