I think I want to find a IH 1460 this year, since I got some more acres. My 715 just takes too much gas for 200+ acres a year. What do I need to look for on the 1460, I am really excited about going to a rotary machine, never ran one before,, I have ran on 4400s, 6620s, 8820s, 715, MF 510, JD 9500, but dont have any rotary experience. Also wondering If anyone was looking for a real good 2nd owner 715 hydro, with 843head, the 301 engine was rebuilt a few years back, new concave/rasp bars then too. Several other new parts, or should I try to sell the engine and part it out, I guess I could put it in the combine demolition at the fair this year. That looks pretty fun, but I hate to see this good of machine to scrap. Would also like to go to a six row machine. Thanks guys you are always good help and advise
 
Where in Iowa are you located? I might be interested in the 715. Don't make it into an engine donor if you can help it unless it's wore out.

1460 is a good machine, but from what I've seen, used 1440's seem to be in better condition; maybe they were run by smaller operators. For 200 acres, a 1440 would be plenty big enough, but either one would work for you.
 
The 1460 is the way to go. Can handle 6 row head easy. The 60 has heavier finals and trans than the 40. If in the hills I would never put a 6row on a 40. When looking check the grain bin floor under the left side, they are always wore out there or thin, other than that look at ovious and the front axle for welding and etc, any more ? feel free to email me. PS I have worked on these for some time and ran a 1420 for 5 years.
 
Dont junk the 715.Someone will want it.

The IH AF's really do a good job.Finding a 1460 that isnt worn out may be a challenge.Theres very few left running in my area.
 
I am in NE Iowa, from West UNion. The 715 is a pretty good old machine, it was shedded every year, except the one before I bought it. The guy I bought it from was the mechanic for the original owner, so I guess I am the 3rd owner, but I know the first two are neighbors/friends. It had an overhaul, concave, rasp bars, a few years ago, a new feederhouse chain 2 or 3 years ago. Its the heavy 1460 chain. Run good until end a year, I had to switch radiators and I got one of a junk machine, but I think it needs to be cooked clean, because it wants to get too warm now, but I borrowed a machine to finish up last year so I didn't hurt the engine. It has plenty of power, good hydro. Can combine beans with 13 or 15 ft head a just a little over a gallon acre gas, corn is more like 2-3.
 
I have seen several machines advertised in the the 3000 hr to 5000 hr area. Do you think the ones around 3000 are wore out? Also have seen prices from $4000 to $20000, what a range?
 
Corn and bean combines usually need alot of work at 3000 hours in high yield areas..Ones over that probably have been rebuilt at least once.

The best 1460's will be found in wheat country.They last a long time cutting 40-50 bushel wheat and 70 bushel milo.Several neighbors always got their used combines out of Kansas.
 
We have cut up to 140 acres of 40 to 50 bushel wheat in one day with our 1460. Bought it with 2400 hours on it, engine shot at 2700 hours - bad cam lobe and the bearings were down to the brass. We usually run about 1700 acres of wheat through ours every year.

Overall, a good machine - my brother-in-law ran one to 7200 hours and never rebuilt anything (mostly wheat and some corn). They finally traded it off because it was burning a couple gallons of oil per day and had to be held in 2nd gear with a tarp strap.

Just keep in mind, that when they need to be rebuilt it can get spendy. We put $5000 in the engine on ours. The rotary parts aren't cheap either when they wear out...

And, the 1460 is twice the machine a 1440 is - more horsepower, heavier components, more grain tank capacity, etc. But for 200 acres, a 1440 will be plenty.

1460_1.jpg


1460_2.jpg
 
I searched for a couple of years for a 1460. I could not find a machine meeting mycriteria,
always felt they all required repairing and this can get to be costly. Finally run unto a 1640, very low hrs, lot of money, but looked at the long term investment and return. Very happy with the performance last fall.
Have you priced the bean and corn heads? They will cost as much as the combine for good units. The only suggestion I can make on the 1460, look for a later model with hydraulic/electric controls for better flex head performance. In regard to selling your 715, I advertised my old machine, had it for 24 years locally for a month, never got a call. Placed in on the in the YT photo ads sold within a month, got calls for the next 2 months. Good luck with your search.
 
the only difference between a 1440 and 1460 is heaver final drives and tranny and a turbo'ed motor. Other then that the cleaning capacity is the same as a 1460.
 
For god sakes, for your own good, don't mention anything around here about combine derbys, you'll get attacked:) Anyways, I think you will like having a rotor. Just updated to a 1680 and sold our 1440, our 1st rotor. Was a good machine, that would run alot of acres with minimal downtime. Ours had a turbo and RWA. Also had just over 4000 hours when we sold it. Ran a 6 row fine, and 16 1/2 foot 820 flex. just added the 3rd cylinder. 200 acres will be no problem for a 1440/60. Good luck.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top