2900G engine into 190xt

joeysmith

Well-known Member
Tractor was gas an had a piston come apart breaking a liner.
Set long enough the 2800 gasser that was in it its now a boat anchor.

I started this project a few years ago an just kina getting back to it.

The combine oil cooler am filter setup has interference issues in the tractor.

Anyone's opinions on just running the filter an housing off the 2800 gas engine?

Its just a 1 filter setup vs 2 the combine had.

Tractor wont see much heavy work and if it does it'll be running a 14ft swather or 535jd baler for a few hours

Doubt it ever sees a plow again in its life unless its just piddling around.

Any other issues ill run into with the swap?
 
What age and model combine did this combine engine come from?? Usually combine engines have no provision for a hydraulic pump on the left front corner ?? and you have no parts from your old gas engine to convert the combine engine to a hydraulic pump drive. I don't see what your oil filter issue is?? the filters clear the side frames ?? or does this engine have a coolant tube that goes across the rear of the engine ??
 
What age and model combine did this combine engine come from?? Usually combine engines have no provision for a hydraulic pump on the left front corner ?? and you have no parts from your old gas engine to convert the combine engine to a hydraulic pump drive. I don't see what your oil filter issue is?? the filters clear the side frames ?? or does this engine have a coolant tube that goes across the rear of the engine ??
Yes the combine engine has the big wrap around oil cooler with the 2 filter setup.
The filters hit the frame and the back tube hits the clutch arm.

I machined out the front cover to accept the hydraulic pump.

I do still have the gas engine an parts of which the oil filter housing will fit the diesel but its just 1 filter an no cooler.


The combine engine plate
1000029167.jpg
 
If you get the block stripped down to where that single (gas engine) oil filter base fits the block, determine if that passage in the rear of the block is open all the way across from the left rear corner to the right rear corner of the block. At the right rear corner the rear cross passage meets the main oil galley which goes from the right rear corner to the right front corner of the block. If this is open you are good to go. If there is a spring and plunger in that rear cross passage, remove them with a magnet to make things open for oil to flow. Yes, you will not have an oil cooler.
 
If you get the block stripped down to where that single (gas engine) oil filter base fits the block, determine if that passage in the rear of the block is open all the way across from the left rear corner to the right rear corner of the block. At the right rear corner the rear cross passage meets the main oil galley which goes from the right rear corner to the right front corner of the block. If this is open you are good to go. If there is a spring and plunger in that rear cross passage, remove them with a magnet to make things open for oil to flow. Yes, you will not have an oil cooler.
I will check that
Thank you
As far as filtration goes the 1 filter should be ok in your opinion? Tractor will sit most the year.

Another question I guess does the gas engine cooling system have a chance at keeping the diesel engine cool you think?

Or do i need to bite the bullet for a new radiator?
 
Water pumps are the same impeller. Radiators are the same core thickness I think. All you have to do is keep a good fan belt tight and radiator core washed out clean and if you do have overheating, just reduce the load and the temps will come down. Worst case scenario is 100% HP output on a 90 degree day. 100% HP output on a 60 degree day is a whole lot easier to keep cool. Chane the oil every 75 hrs instead of 100 hrs.
 
Water pumps are the same impeller. Radiators are the same core thickness I think. All you have to do is keep a good fan belt tight and radiator core washed out clean and if you do have overheating, just reduce the load and the temps will come down. Worst case scenario is 100% HP output on a 90 degree day. 100% HP output on a 60 degree day is a whole lot easier to keep cool. Chane the oil every 75 hrs instead of 100 hrs.
Perfect
It'll be lucky to see 75 hrs in 5 yrs.

Should probably just scrap the ole girl but it was grandpa's tractor ani knew the guy he bought it from so its kina sentimental.

Thanks again for the information!!
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top