6 to 12 volt conversion question ,Advice Req.

I have a 8N-B which presently is factory standard 6 volt. I an considering changing to 12 volt but wish to keep it looking as close to factory as possible.FARM SHOW vol.1/2009 has an add from G&R rebuilding of the generator,starter & requlator with the following comments:....N starter drive comes in backward and with 12volts it will turn so fast it can tear up your flywheel. ? is that true??? they suggest to rebuild the starter also for 12 volt also? is that the case also??THANKS,Phil...Cost is about $150 each + ship to St,Paul,MN. ouch
 
I converted our 861 to 12 volt 15-20 years ago and have never had any trouble with the starter, flywheel nor anything else. If you don"t stay on the starter too long, it will work fine. Only thing you need to do is alternator/generator for 12V, 12V battery and coil with proper resistance to keep it from melting. That said, both my 8N"s are still 6V and work fine as well.
 
Phil.....yer shootin' yerself in the foot ...er... electricals 'cuz you don't understand.

Yes, you can convert yer 6-volt genny to 12-volts for a "stealth" conversion that looks stock, but why? Then you need the matching 12-volt squarecan voltage regulator. The commonly used Delco 10-SI alternator has built-in solidstate voltage regulator and is so simple and CHEAP to use. You doubt? Rebuild alternators about $35, checked and tested junqueyard alternators $20. Your call.

You write....."N starter drive comes in backward and with 12volts it will turn so fast it can tear up your flywheel. ? is that true???".......well, I suppose you could call the N-Starter drive backwards, its just different than modern starter drives. And yes, 12-volts on a 6-volt starter turns it very fast for quicker starting. Its the LAW. Electrodynamics Law. and NO it doesn't tear up yer flywheel ring gear. such rubbish!!! .......respectfully, Dell, a 12-volt advocate for the right reasons. That said, I haven't found the right reason for my eazy starting 6-volt 52-8N and I know how to do it right the first time. Infact I know 8-ways to do it and they all work.
 
Whats your reasoning for going to 12 volt? This always starts a heated discussion around here! :lol:
 
Do yourself a big favor and leave it 6 Volts..Lots of times 12 volt systems are used to vober up a problem. If everything is working right the 6 volt starter will start the engine before it turns over a complete revolution..
 
I have six old Ford tractors. The first five all have original 6 volt system and start without any problems - some have less than ideal compression, too. The lastest addition is a '39 with 12 volt alternator and a birds nest of wires. It starts well too but I can't wait to convert it back to 6 volt.
 
most of the time original works best but 12 volt is to much hassle until you work the kinks out. but your money do as you think is best... resectfully
 
I've got 6v fords with 6v starters that work fine..and 12v fords with 12v rebuilt starters. .. and 6v starters..

they all work fine.

Me? If I had to go to 12v, but wante dthe gen look.. I'd get the gen rebuilt as 12v and get the new regulator and the 12v battery and keep the starter the way it is unitll it needs service.

soundguy
 
Thanks for the comments and advice. It does start reliability when cold (near 0 degrees here in NW Indiana this year.) It was just a consideration that I see fairly often.Thanks Again
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top