carburetor ????

Anonymous-0

Well-known Member
Hey folks,
I had been fighting and crying over my ATV for quite a while and finally found a carburetor w/ manual choke and simpler design (Mikuni). Thing is, in order to find the correct inlet/outlet measurements I ended up with one thru 150cc. My motor is 250cc. Starts and runs fine, but when I really open it up it acts like it wants to run out of gas. Let off the throttle a little and it runs along just fine. Is it as simple as an adjustment, or installing larger jets? If you need more info, steer me to it.

Thanks, Dave
 
If the bore sizes are different, then you probably don't have enough carburetor to handle the CFM of your bigger engine.

Does this carburetor have a slide? If so, you can enrichen the mixture by moving the clip that retains the main jet needle in the slide. But don't do that unless you're sure that the mixture is really too lean. You need to run it awhile and read the plugs to tell for sure.

Is this a constant velocity (CV) carb? CV carbs can be identified by a diaphragm on the top or side of the carb. The diaphragm operates the slide, which on non-CV carbs is operated by the thottle cable. It's possible that the slide is opening too fast or slow for your engine. This can be tuned by changing the diaphragm spring.
 
(quoted from post at 02:55:16 06/08/09)
Does this carburetor have a slide?
Is this a constant velocity (CV) carb? .

Does this help?
a2214.jpg


It says VM in the descrption.

Dave
 

I'm thinking that there is probably a difference in the size of the venturi between the carb for a 150cc machine and a 250cc machine,if that's the case,your engine will run ok until it gets to the point where it can't pull enough air through the carb.You could try increasing the size of the main jet,but that's going to leave more fuel in,it may make it worse if it can't pull enough air to mix with the extra fuel.
 
Did you by any chance replace a CV carb with this one? The behavior you describe sounds a lot like typical behavior for a non-CV carburetor. Will the engine rev up to full speed under load if you open the throttle gradually? If so, then there's not much to be done. Raising the main jet needle a notch or two may help.
 
my yamaha yfm 250 b acted the same way. Shop put in new carb kit (aftermarket for mikuni) & adjusted; runs great now. I think you just need it adjusted.
 
(quoted from post at 18:32:30 06/08/09) Did you by any chance replace a CV carb with this one? The behavior you describe sounds a lot like typical behavior for a non-CV carburetor. Will the engine rev up to full speed under load if you open the throttle gradually? If so, then there's not much to be done. Raising the main jet needle a notch or two may help.

I sure did.... The replacement carb was 300+ bucks, I got the one in the pic for 65. I took it out of the box and installed it, so adjusting is probably in order :roll:
 
(quoted from post at 23:10:24 06/08/09) my yamaha yfm 250 b acted the same way. Shop put in new carb kit (aftermarket for mikuni) & adjusted; runs great now. I think you just need it adjusted.

We probably have the same machine. mine is chinese made but the parts/motor are Yamaha. Bear tracker/bruin is pretty much the same as what I have.

Dave
 
You'll learn to live with it. A CV carb works like the secondaries on a typical four-barrel carb: The slide opens just enough to supply the volume of air-fuel mixture that's required. By replacing it with a non-CV carb, it's like replacing a quadrajet with a Holley double-pumper, then disabling both accelerator pumps. You're not going to get the smooth response you had with the old CV carb.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top