Anonymous-0

Well-known Member
i have a 1990 chevy pickup 5speed, with a blown tbi 350. i want to fing a carburated motor out of an older truck and put it in. will i still need to keep the computer for anything? how would everything wire up?
 
It'll be WAY easier and cheaper finding a throttle body 350 to bolt in and hook right up.1987-1995.
 
You need to change the fuel pump (or use a regulator).

Use an older HEI distributor with a vacuum and centrifugal advance and a NON-feedback carb, and that should be all you need, since it's a 5-speed mech tranny.

All you'd need for it to run would be to take the RED 12-Volt wire that went to the coil, put a different end on it, and connect it to the "BATT" terminal on the older HEI.
 
(quoted from post at 08:13:59 03/12/09) You need to change the fuel pump (or use a regulator).

Use an older HEI distributor with a vacuum and centrifugal advance and a NON-feedback carb, and that should be all you need, since it's a 5-speed mech tranny.

All you'd need for it to run would be to take the RED 12-Volt wire that went to the coil, put a different end on it, and connect it to the "BATT" terminal on the older HEI.

FI Fuel Pump will need to be changed or regulated down. Too much pressure for a carb. Truck may not be smog legal in some areas if you do the mod. You may want to do a little homework before you jump into it. good luck.
 
For curiosity's sake. At least talk a walk through the used truck lot and look at an early to mid 2000's vehicle.
It will give you a baseline of what a newer lower mileage vehicle would cost. V.s. parts, time,labour and $$$. With the results being a 1990 pickup.
The computer will be required for dash instruments, AC, cruise etc to operate. Unless you are an electrical/electronic whiz. This truck will never run like it used to.
If nothing else drop the carb idea and rebuild/replace the existing engine for the "same". Those GM crate engines are priced right, are high quality and have excellent warrenty. Everything bolts together without pieces left over.
 
D17, is it your plan to run straight alcohol in this carburated truck? This is the only big reason that I can see for wanting to expend the effort needed to retrofit your engine. Keep in mind that if this is the case, you may not want even a standard carb, as most(All) use neoprene floats, vice brass. Others who have done this tell me that they needed to change the intake manifold, and retard the timing.
 
I have a good 350 sitting here, but like others have said, you won't have much luck with your instruments on the dash. The other thing you could do is find an old 350 short block and put your heads, intake, and TBI on it. Not worry about retrofitting everything. I have done that before. Anymore it seems that TBI is old school and just as easy to work on as carb. Do not put your TBI intake on the heads of an older 350, it looks close, and some people will drill out the holes to make it work, but it will not run very good. Had this experience with a truck I bought.
 
What do you hope to acheive with this engine swap?

Poorer gas mileage?
Worse performance?
Less reliability?

Well you don't have to compromise, because by installing an older, carbureted engine you will get all three, plus you get to generate a few more of those greenhouse gases that everyone here seems to love.
 
if you have access to an older engine they make a kit that screws into the 2 center bolt holes in the head to put the T.B. intake on the carb heads.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top