Cutting beans with a rigid head

Anonymous-0

Well-known Member
How well is my 13' rigid head going to cut beans? That's what you used in the old days right? Do you set it real low, go slow and really pay attention, or is there an easier way?
It don't look like to me that it will float hardly at all, the guards look like they will gouge the ground. Does anybody have any tips or tricks?
Thanks,
Brett
Combine021.jpg

IMG_1050.jpg
 
If you have head Control ,, Should Do reasonably well unless You have disc ridges in the Field,, I use a 10and 13 ft Rigid head on a Couple Massey 300s.
 
Hart-Carter, Love,Hiniker maybe others made floating bars that would bolt onto the rigid heads. Robot made a header hight control.
 
We had a 55 in the pre-Hiniker bar days and this is how it was set up for combining beans. It had the platform float spring attachment which included steel skid plates bolted to the bottom of the header. With these skid plates on, you could then put the header on the ground and then just keep an eye on the platform float spring indicator. The cutterbar wouldn't flex, but since it was sitting on the ground all the time you could shave the beans off fairly close to the ground. But soon after the Hiniker bar was introduced, we bought one and put it on that combine. But we still used the platform float springs and I could run it side-by-side with my uncle's 6620 Titan II with a 915 flex head and you could not tell who was doing the better job of shaving the beans off!
 
The first soybeans I ever cut was with a 300 Massey with a 14 foot rigid head near Greensburg. (Maybe that should be the town formally known as Greensburg) Anyhow I and the boss were pleased with the job I could do with it. Any wider and it would have been a challenge but 14 foot was manageable.
 
Hate to throw water on your fire but IMHO the beans you will leave in the field will more than pay for hiring someone w/ a flex head and preferabley an air reel. If you have both in the same field, the difference will be very obvious and you will not be long parking the old sow. Particularly with $13/bu beans.
 
If your fields are perfectly level and you have beans that dont pod low to the ground you will get by.If the beans pod low you will waste alot of them.

I have cut many an acre with rigid heads on a E Gleaner and a 403 IH.The 403 had an M&W Robot Header Control which sure worked nice.

When I got my new 1975 715 IH Gas Hydro I got a Hart-Carter add on flex bean bar which really shaved the ground.It was one of the first flex heads in the neighborhood.
 
Plow furrows will leave a lot of beans out there, and you'll e scooping dirt out until you get the hang of it. :)

Can be done, but you will leave some beans. If you drive too slow, the combine doesn't fill up & won't thrash right and you lose beans that way too.

But, it can be done.

Narrow header & flat fields and you need to keep your hand on the header lever 100% of the time, moving up & down an inch every few moments.....

--->Paul
 
I used to cut around 450 acres of beans a year with a 95 combine and 13" ridged head up intle 3 years ago when i got a floating cutter bar. Here is a trick i learned. I got three spring loaded header pickup guards and placed one at each end of the header and one in the center(place them so they will not be on a row of beans). I would watch them and if one started to raise up i would raise the head, when it went down i would lower the head. This worked great. Another thing i did was put float springs on the feeder house. What worked out the best was i would row my soybeans and cultivate them so they where up on ridges. I know also one year the ground froze before i could get my beans cut and that worked great because the header wouldnt dig dirt it would just slid along the ground! Hope this helps.
 
What everybody said plus Rocks, yes you'll find em and unfortunately in the wrong places. A cultimulcher would be good at planting time for leveling and pushing rocks down and no-till beans are out the window because you just can't see through that ground trash especially at night.Oh yea a big bottle of Advil would be nice for the stress and and eye strain after a few hours. My two cents CT
 
We did fine cutting with locked up 18' flex heads on JD 9400s. We went back to using flex all the time last year. About five or six years ago they were cutting some wet beans with water standing in them and several ant mounds. They locked them up and found they performed much better. They never unlocked them again until year before last when dad rebuilt the skid plates on one. That was part of the reason for running them rigid; they drug up much less when things started getting damp at dusk. If you don't have automatic header it would be fine. That being said the automatic header is very nice and you can't use it with rigid heads and there are times when a flex head is the only way to get every last bean. On level ground it does just as good a job and floats right along.
 
Have run a JD 55 and Gleaner K's with 13 ft rigid heads. 13 ft will work fine. Just pay attention and make sure your field cultivator does a good job of leveling. It can be frustrating at times, but you can do ok with alittle patience. Run as low as you can without digging the dirt, is how I always did it. My dad had a 55B that had a rigid head with a skid underneath it, and it seemed to do an alright job. If you have alot of bean acres you might want to find a JD 200 series flex and adapt it to your machine. They seem to work OK with out the auto head. Good Luck.
 
Works fine with a little practice-gets pretty difficult with anything over a 15' rigid head if ground is not level. If you can't do a good job combining with a 13' rigid head, you are a combine driver, not a combine operator!
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top