Engine Overhaul

Anonymous-0

Well-known Member
I have a 1949 8N 4 CYL that needs an engine overhaul. What is the best In frame engine overhaul kit I can get for my money? What type do I need (Bore size, piston liner size .040 or .090) ect?

Thanks
RDAllison
 
(quoted from post at 23:27:21 05/12/09) I have a 1949 8N 4 CYL that needs an engine overhaul. [b:77671770ca]What is the best In frame engine overhaul kit I can get for my money? [/b:77671770ca]What type do I need (Bore size, piston liner size .040 or .090) ect?

Thanks
RDAllison

I will stay out of this one.

That isn't an overhaul.
 
Nothing wrong with an in frame overhaul in my book. The way most of us run our tractors an in frame will last for years. However, one disadvantage to owning a flat head is unless you do the valves too then it's really not worth putting the new sleeves and pistons in. If you knew someone who could come over and recut your seats in frame then I would do it. Otherwise I would just do rings and rod bearings. Assuming you had decent oil pressure before and did a compression test too.
 
It has good oil pressure 25-30. I have not done a compression test. I don’t have the equipment. But when it's under any kind of load it just starts losing power and making an awful lost lot spitting noises and choking (I cant really describe the sound). And it runs kind of noisy like something in the engine block is messed up. I figured it needed an engine overhaul.
Would that be correct?
I found a overhaul kit at www.allpartsstore.com
It's an A&I part.
To tell you the truth I have never worked in a in frame engine before, besides a lawn mower and I just took it apart...didn’t worked well after that.
Thanks
RDAlliosn
 
Sounds to me like you have carb issues.The carbs on these motors are so good when the fuel cutoff in the carb sticks open extra gas gets sucked into the motor.Then run like you described,no power cough spit die under load.Compression tester might be a good investment in your case.HFT$10 cheap. Fred
 
(quoted from post at 02:17:32 05/13/09) It has good oil pressure 25-30. I have not done a compression test. I don’t have the equipment. But when it's under any kind of load it just starts losing power and making an awful lost lot spitting noises and choking (I cant really describe the sound). And it runs kind of noisy like something in the engine block is messed up. I figured it needed an engine overhaul.
Would that be correct?
I found a overhaul kit at www.allpartsstore.com
It's an A&I part.
To tell you the truth I have never worked in a in frame engine before, besides a lawn mower and I just took it apart...didn’t worked well after that.
Thanks
RDAlliosn

I think you really need to do some more diagnostic work before you commit to an overhaul. And if the overhaul is what's needed I suggest you enlist the services of someone to help or do it for you. No offense but if your lawnmower overhaul didn't turn out well your prospects for a better outcome on a DIY N motor overhaul aren't good.

V/R

TOH
 
RDAllison......you write......"when it's under any kind of load it just starts losing power and making an awful lost lot spitting noises and choking".......it aint'chur carb ittz'chur sparkies!!! You doubt? Make a calibrated sparkie tester outta enny ol'sparkie. Bend the side electrode out for full 3/16" gap. Clamp the metal shell to convenient bracket and plug enny sparkie wire to the top connection. With ignition on, crank yer engine over with starter motor while WATCHING the calibrated tester. Do the sparkies jump the gap with blue-snott authority? or are they wimpy yellowish-orangish poor excuse? or no sparkies ever??? Report back and we'll tell you how to fixx'em ........Dell, yer self-appointed sparkie-meister
 
You really need to figure out why it's acting the way it is before you decide to do an overhaul. It may just need a tune-up or carb rebuild. If all you did to the lawn mower was take it apart it's no wonder it didn't run well after that. You need to put it back together! ;+)
 
What you're describing sounds like tune up/carb problems more than "needs an overhaul". Like the others suggested I'd do some more diagnosis before you trash your tractor.
 
That was when I was 11 and the engine was already shot, But your right I need help if I was going to overhaul. I just took the 8N for a test drive, It only makes that noise after is been running for over half a hour or if the load is strenuous like a pto attachment that’s to big. I need to get a new carb any way because I pulled the mounting bolt thru the carb mounting face. It just didn’t seem tighten down.
I have to wait till we go into town to pick up the compression tester.

Thanks
RDAllison
 
I took a old spark plug and bent the side electrode out, not sure how far but farther then my gaper went and tested the sparks were blue a bout 1/5 of the time, the rest where Yellow/orange, but they were pretty strong.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top