flooding carb

manni52

New User
Hello, all-

I have an early Ford 8N with a Marvel Schebler carb TSX241C. I had recently put new parts in from a kit. The tractor runs ok for a while then just stops and will not start. I discovered liquid fuel running out of the choke housing, lots of it. The first thing I checked is the float level, it is good if not on the low side, also it is not saturated. The gaskets all seem to be sealing properly. After I assembled the carburetor I set the idle and air fuel mixture both at one full turn off seat. I have not been able to properly tune the carb and governor because I do not have a proof gauge to properly adjust for RPM. The only thing I changed when I assembled the carb was I added the economizer jet from the kit which was originally missing. I am not very familiar with this type of carb so my question to the forum is, am I missing anything re: this serious flooding?
Thanks in advance!
-John
 

You probably don't have any flooding. If you are cranking the motor it should be drawing air and gasoline with it. If it does not fire and run in a turn and a half, since it is an updraft carburetor, all of the gas that has been drawn up into the manifold is coming right back down. It is perfectly normal. If you pull the plugs and they are all wet, then you may have flooding.
 
(quoted from post at 11:03:04 11/04/17) Hello, all-

I have an early Ford 8N with a Marvel Schebler carb TSX241C. I had recently put new parts in from a kit. The tractor runs ok for a while then just stops and will not start. I discovered liquid fuel running out of the choke housing, lots of it. The first thing I checked is the float level, it is good if not on the low side, also it is not saturated. The gaskets all seem to be sealing properly. After I assembled the carburetor I set the idle and air fuel mixture both at one full turn off seat. I have not been able to properly tune the carb and governor because I do not have a proof gauge to properly adjust for RPM. The only thing I changed when I assembled the carb was I added the economizer jet from the kit which was originally missing. I am not very familiar with this type of carb so my question to the forum is, am I missing anything re: this serious flooding?
Thanks in advance!
-John

fix the float level if it is low. close don't count.
 
I was going to say the same thing showcrop did. Suspect no spark.

The MarVel is a side-draft carburetor, isn't it? Doesn't matter; it does the same thing as an updraft: the carb appears flooded after cranking without spark.

The Stewart carb on my '22 Dodge Bros. is an updraft, and it does the same thing.
a177197.jpg
 
John,You might have some trash under the needle valve ,or the float hanging up on the sides of the bowl.Shake the float and listen/feel for gas in it.Before it died was it putting out a lot of black smoke?
 
(quoted from post at 21:46:50 11/04/17)
(quoted from post at 11:03:04 11/04/17) Hello, all-

I have an early Ford 8N with a Marvel Schebler carb TSX241C. I had recently put new parts in from a kit. The tractor runs ok for a while then just stops and will not start. I discovered liquid fuel running out of the choke housing, lots of it. The first thing I checked is the float level, it is good if not on the low side, also it is not saturated. The gaskets all seem to be sealing properly. After I assembled the carburetor I set the idle and air fuel mixture both at one full turn off seat. I have not been able to properly tune the carb and governor because I do not have a proof gauge to properly adjust for RPM. The only thing I changed when I assembled the carb was I added the economizer jet from the kit which was originally missing. I am not very familiar with this type of carb so my question to the forum is, am I missing anything re: this serious flooding?
Thanks in advance!
-John

fix the float level if it is low. close don't count.

I agree with Mr. Geiger. Improper float setting can cause over filling the carburetor bowl. The excess fuel will spill into the carburetor air intake when the engine stops running.
 
(quoted from post at 02:53:19 11/05/17)
(quoted from post at 21:46:50 11/04/17)
(quoted from post at 11:03:04 11/04/17) Hello, all-

I have an early Ford 8N with a Marvel Schebler carb TSX241C. I had recently put new parts in from a kit. The tractor runs ok for a while then just stops and will not start. I discovered liquid fuel running out of the choke housing, lots of it. The first thing I checked is the float level, it is good if not on the low side, also it is not saturated. The gaskets all seem to be sealing properly. After I assembled the carburetor I set the idle and air fuel mixture both at one full turn off seat. I have not been able to properly tune the carb and governor because I do not have a proof gauge to properly adjust for RPM. The only thing I changed when I assembled the carb was I added the economizer jet from the kit which was originally missing. I am not very familiar with this type of carb so my question to the forum is, am I missing anything re: this serious flooding?
Thanks in advance!
-John

fix the float level if it is low. close don't count.

I agree with Mr. Geiger. Improper float setting can cause over filling the carburetor bowl. The excess fuel will spill into the carburetor air intake when the engine stops running.


The design of the float chamber part of the carb is such that the fuel flow is shut off once it reaches the proper level. If it were by any means, including that the float was set low enough for the gas to overflow, able to rise and overflow once the engine was shut off, It would drain the tank.

Manni, Before digging into your carb again, check for spark. That is much quicker.
 
(quoted from post at 12:03:04 11/04/17) Hello, all-

I have an early Ford 8N with a Marvel Schebler carb TSX241C. I had recently put new parts in from a kit. The tractor runs ok for a while then just stops and will not start. I discovered liquid fuel running out of the choke housing, lots of it. The first thing I checked is the float level, it is good if not on the low side, also it is not saturated. The gaskets all seem to be sealing properly. After I assembled the carburetor I set the idle and air fuel mixture both at one full turn off seat. I have not been able to properly tune the carb and governor because I do not have a proof gauge to properly adjust for RPM. The only thing I changed when I assembled the carb was I added the economizer jet from the kit which was originally missing. I am not very familiar with this type of carb so my question to the forum is, am I missing anything re: this serious flooding?
Thanks in advance!
-John
b:04f37563c1][i:04f37563c1]

manni52...John;
Re-reading your post, and note that you say......" The only thing I changed when I assembled the carb was I added the economizer jet from the kit which was originally missing."
My ?? is......did/was that carb running before you installed the econo jet.?????
If the answer to that is YES.......remove the econo jet and run it without one.
Post back with your results.!!!!
The TSX 241C, had it's problems in that area, and was pulled out of service with only approx. 4-5 mos. of use!!!
Not to say that it will not work.....just have to know the right jets to use, and sizing of their oriface!
Some TSX 241C's NEVER used the econo jets, others had to have them!!!!

Waiting for your answer???!!!
Gary :?: [/i:04f37563c1][/b:04f37563c1]
 
Hey folks, thanks for all of the replies! I have not completely got the hang of this forum communication so I hope all who desire a reply will see this. When I said the float level was perhaps set on the low side I meant that the needle and seat would seal early maintaining a lower level of fuel in the carb, ensuring that the gas would not reach the vents. I have spark, at least when I checked for it, may be intermittent? I went through the distributer and replaced the electrics as well as the cam and weight assy. The tractor Is doing now what it was doing before I started to hanky with it, runs fine for a while and then stumbles and quits, and will not restart, thanks to this forum I have been educated that repeated cranking with out spark will dump gas back into the intake so my diagnosis of flooding could be incorrect. I will remove the economizer and reassemble the carb I will no be able to press it back into service until the snow melts, however.
Thanks again for all of your input!
 
[b:b2927b000d]Den N Ms[/b:b2927b000d]: sorry did not answer your ?
No was not blowing black smoke, another good point. Did not look or smell like it was running rich.

Tx!-J
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top