Hard starting 970

RGMartin

Well-known Member
Looking for some thoughts on a hard starting 970.

3400 original hours(in family for 30+ years). Oversized starter(40 series Delco ???), cables and batteries. Below 70 degrees she will not start without either. Below 40 she just won't start. Starts fine if she has run within the last 8 hours or so. Not much use over the last 15 years, some years none. Last year I put 25 hours on her. Seems down on power, will pull 4 bottoms in the same gear she used to pull 5's.

Has had all fluids and filters last year. Adjusted valves.

Turned the max fuel screw a hair trying get the power back, can get a slight haze out the exhaust, no real black smoke though.

No more blowby out the breather than any other 70 we have here.

Any thoughts? A major overhaul would be nice, but the $ won't be there for at least a year.
 
I assume you have checked for fuel flow
Are you getting white smoke when you start cranking?
If not check for fuel leak off in lines. If you are getting white smoke you may have injector problems or pump problems. Really sounds like she is worn in a lot of places and needs compression check run. Have to go from there
 
I worked on a 970 last year that did the same thing. I checked the compression and it was very low. I pulled the pistons and found many of the rings where set in the grooves. This will happen from sitting so long without being run.
 
WE had the same problem on tractors that sat a long time. Take her out and work her as hard as posible for a day. Try plowing or some other field work that will keep a constant pull on the engine for a while. You should start to see an improvement after a couple of hours. Of course if your engine is truely shot you won't see much improvement.
 
(quoted from post at 09:48:33 01/09/12) I assume you have checked for fuel flow
Are you getting white smoke when you start cranking?
If not check for fuel leak off in lines. If you are getting white smoke you may have injector problems or pump problems. Really sounds like she is worn in a lot of places and needs compression check run. Have to go from there

White smoke almost immediately. Good stream of fuel when I pull the line off at the lift pump.

Most of the hours last year were plowing and discing as fast as it would pull the implement.

If the rings are set/stuck, would it be worthwhile just to put new rings on the original pistons? I think already know the answer.
 
Was timing ever changed?When cranking engine are you getting white unburned fuel out exhaust?Sure cranking speed is fast enough?
 
If it's a Yellow tractor Try the Hand pump by the fuel filters /The 1 Way Vales may have dirt,hay ,hat ever Plugging them Off.Had that problem with my 870 25 years ago/all most turned up the Fuel I was so mad at it, [Sure Glad I never did ,still set factory ]It was doing the same thing yours is. might be the fuel pick up has some thing in it.or the fuel Shut off?
 
All good posts but please make sure the fuel shut-off lever on the injection pump is all the way forward when in the run position.
 
I wouldnt be suprised if you didnt have delivery valve seals cracked in your injection pump. This will cause you to loose some, or all of the high pressure fuel from going to a cylinder. Most guys notice hard starting, then a loss of power. When you rev it it up under no load does it sound like a flutter?. Bosch inline pumps are famous for this. Most guys dont know this . They pull the pump off and send it to town for a 1500 dollar repair bill. The seals and o rings cost less than 50 bucks. If I can help you give me a call 231.757.0064 Ask for Al (pumpman)
 
(quoted from post at 23:04:05 01/10/12) I wouldnt be suprised if you didnt have delivery valve seals cracked in your injection pump. This will cause you to loose some, or all of the high pressure fuel from going to a cylinder. Most guys notice hard starting, then a loss of power. When you rev it it up under no load does it sound like a flutter?. Bosch inline pumps are famous for this. Most guys dont know this . They pull the pump off and send it to town for a 1500 dollar repair bill. The seals and o rings cost less than 50 bucks. If I can help you give me a call 231.757.0064 Ask for Al (pumpman)


Can you define flutter? Not a word a guy stinking of diesel fuel and grease packed under his nails should know how to use... BUT yes it has a very distinct sound under no load/little load at max RPMS. I would throw a you tube video up so you could listen, but not a snowballs chance in Haiti of her starting today.

Also only revs to 1900rpms at no load, used to go to a little over 2000.

I have tried the easy stuff, timing is right, shut off is OK/replaced, fresh fuel.

Sure would be nice to get another 1000 hours on her before a rebuild.
 
I just went down to my friendly neighborhood diesel shop and picked up a kit. Lots of parts in that package for not much money.

Should I attempt this in with the pump still on the engine? From the schematic I found it appears you just unscrew the fitting from the top and pull out the valve...
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top