House/Barn Electrical Problem

Chuck (CA)

Well-known Member
Got a 30 amp, 110v line running from the house out to the barn. Along the run is a yard light that is supposed to kick on at dusk.
It stopped working.
My son took down the light, cleaned out all the hornet's nest and bat poop and put fresh wiring on it. Checked it with an extension cord, comes on.
Put it back up; it doesn't come on.
Found a loose ground at the circiut breaker box at the house that appears to loop back from the barn and reinstalled it. The light now comes on, but now the barn lights won't come on.
My son is going crazy, and I'm too dumb to figure out electricity, so I'm turning to you guys.

Thanks,
Chuck
 
A loose ground should not have made the light work.
You apppear to have a problem that I doubt can be remote diagnosed. You need someone who knows electricity to work on it before someone gets hurt.

Just my opinion.
 
The light is supposed to be connected between a line and neutral. The outer threaded part of the lamp socket goes to neutral, for safety.
The ground connects chassis to earth. #1 to reduce shock hazard. #2 To increase the chances of the over current protection will open the line.
 
When you say the word "ground" I wonder if youre mixing up or mixin n matchin an equipment ground conductor (often green or bare, a groundING conductor) and a Neutral conductor (often White, a groundED conductor). In your main service entrance the Neutral Buss (where all the white neutrals attach) and the Equipment Ground Buss (where all the bare or greens atatch) are bonded together unless you just have one common Buss where alllllll the white Neutrals and all the Bare/Green equipment grounds attach.

A what you call a "line" out to the barn suitable for 110 volt service, would rightfulyl consist of: 1) A Black HOT phase wire,,,,,, 2) A White Neutral (a groundED conductor),,,,,,,,,3) A Green/Bare Equipment GroundING Conductor. Then at the barn there should be an "earth ground" (driven ground rods etc) and, of course, that sub panel (or whatever you have at barn) will NOT have the Neutral bonded to the Equipment Ground such as was done at the main service entrance.

Im afraid you could have a bad or open Neutral and/or youre trying to use mother earth as the current return path somewhere in this configuration!!!!!!!!!!!!!!!!!!!!!!!!!!

DO NOT ALLOW ANY LOOSE OR OPEN NEUTRALS. I would check all connections especially where Neutrals are concerned and look for loose or burned or otherwise poor contact.

I hope you are running 3 (i.e. Hot, Neutral, Ground, NOT just 2) wires out to the barn ?????

Again, check all wiring connections ESPECIALLY the Neutrals and if youre not familiar with wiring ID HIRE A PROFESSIONAL because saving a life and/or avoiding a fire is sure worth his expense.

John T Too long retired electrical engineer
 
I second that motion!, I just finished having a new garage Built, had a Certified Electrician Wired it all up, really is Expensive, BUT if You don't know Electricity Better get Someone that does, I'm really Pleased with it... Larry KF4LKU
 
John you fine giver of confidence!
Is this correct! If not what is wrong with it?
Jim
p7137.jpg
 
Yo Jimbo, its a bit hard to read the pic with my bi focals lol but it looks??? the same as what I described to me......

At house Neutral Buss and Equipment Ground Busses are bonded,,,,,,,,Neutral is bonded to Mother earth at house (EITHER up on weatherhead riser orrrrrrrrr in side meter base orrrrrrrrrrr inside the panel however local authorities do it),,,,,,,,,out at the bran sub panel Neutral and Equipment Ground ARE NOT RE BONDED,,,,,,,,,Outbuilding needs a bond to mother earth,,,,,,,,,,,all non current carrying metal enclosures n junction boxes and light fixture housings etc etc are bonded to the Equipment ground

So it looks like thats what the pic shows n if so its right

John T
 
John T Hold down Ctrl and keep hitting the + button ,
no need for bifocals ,but I still don't know what i see you're the electrician.
 
Hey thanks Roy, that works........What you see is Jims diagram of what I said, A pictures worth a thousand words but us lawyers are bad to use way more words then necessary lol

John T
 
(quoted from post at 21:11:02 07/05/09) Hold down Ctrl and keep hitting the + button ,
.

Man... you're a genious!! That, or I've been a complete idiot all my computer using life :roll: :roll:

I've found a whole new world now.....

Thanks
 
No I'm really computer illiterate I can't even down size pics, It just goes to prove even a blind pig can find an acorn once in awhile. LOL, ROF, LMAO.
 
The lawyer I used last had so many words that even confused me so bad that I ended up using my X's lawyer to settle my case in the divorce. and cheaper too.

Now that's being intelligent when her lawyer couldn't legally represent me as a client.

I was at the end of money to fight any longer, it was going to get throw d out as lack of activity so I offered to pay her lawyer what X owed to settle and it worked .
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top