JD 1020 Charging problems

JoeDK

New User
I have a 1966 1020 Gaser. 12 volt system. I am experiencing charging problems. Generator light is on. At first I thought it was the alternator as I was only getting a voltage reading for what the battery itself was putting out with the tractor running, about 12.3 volts (after trickle charging due to the no charging condition). After replacing the alternator I saw no change in the voltage. Through some research, I decided to consider the voltage regulator. I brought direct power to the field terminal on the alternator and the voltage on the multimeter at the battery immediately jumped. Thus, I suspected that the regulator must be faulty. I Replaced the voltage regulator and am still only getting about 12.3 volts at the battery with the engine running. When running and turning on lights, I see the typical drop in volts from the battery. Increasing rpm produces no change in voltage at the battery. So, the alternator is still not putting out a charge. From what I understand, the output should be 14 volts give or take. What am I missing? What should I do next? Thanks in advance for any suggestions.
 
(quoted from post at 21:56:08 06/01/22) I have a 1966 1020 Gaser. 12 volt system. I am experiencing charging problems. Generator light is on. At first I thought it was the alternator as I was only getting a voltage reading for what the battery itself was putting out with the tractor running, about 12.3 volts (after trickle charging due to the no charging condition). After replacing the alternator I saw no change in the voltage. Through some research, I decided to consider the voltage regulator. I brought direct power to the field terminal on the alternator and the voltage on the multimeter at the battery immediately jumped. Thus, I suspected that the regulator must be faulty. I Replaced the voltage regulator and am still only getting about 12.3 volts at the battery with the engine running. When running and turning on lights, I see the typical drop in volts from the battery. Increasing rpm produces no change in voltage at the battery. So, the alternator is still not putting out a charge. From what I understand, the output should be 14 volts give or take. What am I missing? What should I do next? Thanks in advance for any suggestions.

Use a voltmeter or test light and see if there is power on the wire to the field terminal of the alternator, when the key is on and the wire is unhooked from the field terminal If there isn't the wire could be broken or a bad connection and you can track it from there back. Do you have a manual, so you have the wiring schematic to help you trace it out?

Best to say the alternator or charge indicator light is out. Saying the generator light is out, then talking about the alternator can make one wonder which it has.
 

Thanks for the idea. I was also thinking that was my next step. I do not have a wiring diagram but can probably find one on the internet some place.

Yes, I meant to say charging light. I will need to be more careful in my use of terms in the future. Thanks again for your help. Much appreciated.
 
No power at the connector. Will have to see if there is a bad wire. I just sent you an email. Thanks for your help!

This post was edited by JoeDK on 06/02/2022 at 07:10 pm.
 
He said he applied power to the field terminal of the new alternator and it worked. He replaced the voltage regulator after that. He still has no power to the field terminal of the alternator from the harness wire. That indicates to me that there is a problem in the wiring harness, or he got a defective regulator. No need to replace the new alternator for a now known wiring issue.

This post was edited by Jim.ME on 06/04/2022 at 04:15 am.
 
(quoted from post at 12:15:18 06/04/22) He said he applied power to the field terminal of the new alternator and it worked. He replaced the voltage regulator after that. He still has no power to the field terminal of the alternator from the harness wire. That indicates to me that there is a problem in the wiring harness, or he got a defective regulator. No need to replace the new alternator for a now known wiring issue.

This post was edited by Jim.ME on 06/04/2022 at 04:15 am.

Well, I checked the field terminal wire (green wire) all the way back to the male connector on the wiring harness (that plugs into the VR) and I have continuity. I even moved the wires around some in case there was a bad spot that would occasionally appear to be okay...same thing, continuity. I plan to check the other wires as well. Any ideas or additional diagnostic checks that can be completed are welcome. I am wondering if I got a bad VR, despite the fact that it is new. Is there any way to test a VR? Thanks!
 

A wire can check ok for continuity, which is generally done with an ohmmeter or continuity tester leads attached to the ends of the wire in question, no power supplied to the wire from the vehicle system. You need to find where the power is being lost.

In your case turn the key on (I would unhook the primary power wire from the coil terminal while testing to prevent damage to the points or coil during testing with the key on) and follow the wire back from the field terminal of the alternator until you find power (using a test light or voltmeter). I don't have a 1020 Service manual to look at. From other JD manuals of about that vintage with Motorola systems I have access to, I think the field wire on the alternator goes back to the regulator. If there is no power being fed to it by the regulator you could have a bad regulator, or one of the other wires to the regulator could be bad preventing its operation. Is the regulator grounded, does it have power being supplied to it as needed? This is where the manual helps sort things out, as several things are in play at the regulator connection.
 

Thanks for your continued assistance. I have confirmed that I do have power going into the VR (at least into the male connector) from the ignition switch but no power going out the VR through the wire that connects to the field terminal on the alternator. I will keep studying the wire diagram that I have to see if there are other checks that I can do. However, I am thinking that my "new" VR might also be defective. I once again energized the field terminal via a jump wire and the charging voltage spiked so it appears as though the alternator is doing its job.

Again, thanks for your assistance.
 
(quoted from post at 21:14:41 06/04/22)
Thanks for your continued assistance. I have confirmed that I do have power going into the VR (at least into the male connector) from the ignition switch but no power going out the VR through the wire that connects to the field terminal on the alternator. I will keep studying the wire diagram that I have to see if there are other checks that I can do. However, I am thinking that my "new" VR might also be defective. I once again energized the field terminal via a jump wire and the charging voltage spiked so it appears as though the alternator is doing its job.

Again, thanks for your assistance.

If there is power on all the wires that should have it, except the one that "feeds" the field it sounds like a defective regulator.
 

SUCCESS! Thanks all for the help. The new voltage regulator that I bought was defective. Once I tried another one, it worked just fine. In the process, I sure did learn a lot about the wiring of this tractor.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top