John Deere 7700

Anonymous-0

Well-known Member
If nothing happens I should be getting a John Deere 7700 combine in here n the next couple of weeks. It is a diesel combine. I remeber hearing something on here about a service door or something to be kept checked for build up of chaff. Looking for all pro's and cons on the machine. The ole girl looks pretty good to me. I custom bale hay by trade but want to expand into doing some crops as well. I'm not looking to sink a fortune in a combine although I know this one will have some things on it too fix. Still $850.00 is not too bad I think for a purchaseing price and yes it does run.
If all goes well, I will have this and the ole 95 out here both going. Really looking forward too it as is my 3rd. cousin who is a combine superfreak. Thanks guys
 
I wrote this for a guy looking at a 6600, but everything applies to the 7700 as they are basically the same machine scaled up a bit. Hours are what really kill combines, especially the 4,6,7000 series Deeres. If you are hitting over 4000 it's going to need a lot of work to get it to 5000.

The 6600 is not one of my favorite machines but if you need a side hill than I’d say go for it. When you look at it other than the above things if it has a straw chopper on it look at the rear section of the combine, the sheet metal tends to crack around there if the copper is out of balance and I have seen one fall off. Look at the sieves or chaffers, whatever you want to call them, on that era Deere machines they like to crack along the front and rear making it hard to adjust and just about useless because that leaves a direct track to dump grain and tailings directly below. Replacement frames start around $800. In front of the sieves, at the end of the auger bed make sure the fingers are all still there, if they aren’t grain dumps directly to the re-clean auger. Check the bearings on the walkers. Look through from the trap door on the top inside to see if the fish-backs have come loose beat the stuffing out of the inside of the machine. Look on top of the walkers toward the front of the machine, there should be a flap hanging down, if it’s not there it needs one otherwise the cylinder throws stuff straight out the back. There is a door above and below where the feederhouse meets the machine, look at the cylinder and the concaves make sure they aren’t broke. If your worried about rasp bars now’s the time to look too. Make sure the hydraulics work smooth. The hydraulic pumps are known to go out on a regular basis, which isn’t bad but the pump is mounted on the end of the direct shaft to the engine and is threaded on there. After years of rust they get stuck on, you use a torch to get them off, that ruins your core so a new pump will run ya over $1000 to change out. The other big thing to look at on a Deere from that era is the axles going to the outer drives. Look at the splines on them. These machines had a light frame, and if it had a large grain tank extension on it or if it was pulled out of the mud incorrectly the frames sprung, causing other bad things to happen and wear out but a tell tale sign is if the axle splines are worn.
 

If you ever have to do anything to the variable speed/belt assembly for the cylinder drive, be sure to time it exactly per the operators manual when you put it back together!!

It will shred the new belt in nothing flat if you don't and may bend the countershaft, too... BTDT...

Howard
 
Sounds like you got it for a good price, diesel engine is worth more than that. We have run the 6600's for around 15 years now and they have been good machines. My brother has a 7720, and yes it is a much better machine to run and work on, but the 00 series aren't that bad. Fix what has to be fixed to thresh grain and don't worry too much about the rest. We replaced the upper sieve with an air foil chaffer, seems to work well, got one from the bone yard for 100 bucks.I agree once they get over 4500 hrs, you have to work on them more, but usually you can pick up parts cheap from the scrap yard and with a torch and normal tools there is not much you cant replace, good luck with your new ride, post a picture if you get the chance, take care.
plainsman1074.jpg

plainsman1137.jpg
 
They are good machines if they are kept up mechanically, not very fun to work on. We had a 1977 7700 RWA that we bought cheap at an auction for $2000.00, with a 216 flex. Seemed like a good deal at the time. Ran fine through 40 acres of wheat, then went to cut my friends and it blew a seal in the hydraulic pump under the seat. When corn harvest came, the feeder chain went out, the Graintank load auger gearbox went out, and a tire blew. Moral of the story, you get what you pay for. But, the combine had a little over 5000 hours on it too, so she was ready to retire. A neighbor decided to sell his 1440 IH, and we bought that, and sold the 7700, which was very good decision. Not trying to scare you. If you are patient, you'll be fine, you still got a good deal and I don't see how your 7700 could be anymore worn out than mine was. Good luck.
i5237.jpg
 
I wasn't trying to scare the guy away from it, I just wanted him to know what and where to look on the thing, not just for buying it but also getting it field ready because the fewer surprises you get while your trying to use it the happier you will be. Although at $850 if the thing runs you can not go wrong.
 
Gary, I may be wrong here but I believe there really were virtually two models of 7700"s one was the early version non turboed very obvious with a flat flush screen at the radiator and the newer version with a rotary screen. I"m not that familiar with that combine but I once had a farmer trying to trade two older 7700"s for a used Hesston Stackhand 30 I was chomping at the bit but after calling around we just couldn"t get together because after looking at them they had some serious issues like walkers missing out of one and belts frayed to pieces on the other one now we"re talking someone who had a farmstead that looked like a war zone. Anyway is that a newer one or non turboed? The old one I think was 128hp and the turbo version was 145hp.
 
It is a early version with the fan exposed, gear drive I believe as the guy I'm going to be getting it from said that hydro's didn't come out on the 7700's, I've seen em with hydro's but then again you have to take pretty much all you hear with a grain of salt as most people tend to think they know a whole lot more than they actually do.
I know a guy that thinks a 4640 John Deere is a 300HP tractor, he is a idiot! I"ve got a cousin inlaw that is a farmer and he thinks my 4430 won't pull my 22' tandum, I hope he don't tell the tractor cause it don't know its back there. Same deal with the 28' field cultivator, it don't hardly know its back there either.
Keep the information coming guys, I picked up a 71 or 72 model grain truck yesterday C/40 Chevrolet. Will have to do some work on it such as ingnition and carb kitting but otherwise looks like a pretty decent old truck. Was a county dump truck at one time. I got both the dump truck sides and grain sides for it. along with a spare tire nad a pair of drive tires and wheels off of a Big White combine for replacement tires on the 7700, was hoping they would just bolt on but looks like I'm going to have to mount the tires, oh well, been there done that a few times.
 
Good luck with both the 7700 and the C40. We had a C50 that our neighbors uncle bought brand new. After we got it we would let the neighbor borrow it and the would load that thing right up. Just a little 350, 4sp, 6.50/8.85 two speed rear. It had an 18ft box that was too big for a single axle and loaded with soys you could get it to 28-29000 lbs. It didn't like it but it did it year after year. The nice part of those older trucks is it is just like working on a tractor. No emissions, breaker points, and fuzzy AM only.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top