(quoted from post at 19:16:55 11/13/10) .017 hot, and .020 cold. i think rusty farmall gave me the cold setting. worked real good.
Where are u getting .017 ? Like to see them spec’s. Plus there never is a cold spec listed as spec’s are usually listed .017 h the smaller tractors like a b and c’s are listed as .014 h. If you’re setting them .012 h that’s too tight. And once the engine gets to temp your probably at .009. Allis charmers likes to use tight spec’s. Like that.Oh someone needs to come clean, where are you guys getting 17 20 valve clearance. Every manual i read says 12 cold. I've just did an overhaul and wanting to specs but surely dont know what to believe. Mine runs good at 12 but a bit hard to start cold. Also have some blow by no smoke on exhaust just valve cover. Hoping wrong valve clearance will settle it.
Yeah maybe if only a thousands or two but too loose and you’re causing excessive wear from the valve beating on the seat and also the rockerBetter to be too loose than too tight. Better to clatter than burn up your valves!
???but too loose and you’re causing excessive wear from the valve beating on the seat
Yes all true and that’s why there’s a specvalve cooling is the amount of time they stay seated. so adjusting valves you want to be at the loser end of the spec. of course staying in spec. as the valve seat and valve face wears the clearance will decrease. as the cam lobe and push rod and rocker wear the clearance will be greater. lots of times when you are hearing this clatter there is already a problem , beyond just an adjustment. plus give 3 feeler gauges to 3 amatures and you will have 3 different readings. setting valves requires a good feel to feel .001 difference. always better to be .001or even .002 looser than that amount tighter is the way i look at it.
On a M, IH 4-cylinder carbureted engines service manual ISS-1031-1 gives .019 cold and .017 at operating temperature. If arms have indentations worn at contact with valve stem you may need to fudge. If worn best to regrind contacts or find a better set if much needs to come off.Oh someone needs to come clean, where are you guys getting 17 20 valve clearance. Every manual i read says 12 cold. I've just did a overhaul and wanting to specs but surely dont know what to believe. Mine runs good at 12 but a bit hard to start cold. Also have some blow by no smoke on exhaust just valve cover. Hoping wrong valve clearance will settle it.
When you overhauled it did you thoroughly clean the mesh inside the breather housing?Thanks, done some more searching and says 17 or 20 cold also from previous post on here. Going to adjust tomorrow. Valve clearance shouldn't be the cause of little excessive blow by but may if compression to high and going past rings. Was just overhauled and I know I should take it out when warms and hook on to disc or something to break in . Although iam not getting any smoke from exhaust at all. Plugs dry also and close to 100 compression on each cylinder. It's ran maybe 1 hour so far
dont be confused with our spec's of .017. its correct. i dont know what manual or engine they are showing you but that is not a farmall m engine. i could see right away it was a one cylinder and the rockers are also different. there is a model M engine also but that photo is not of it either. of show us the cover and more of that manual. now i think your looking at the john deere "M" tractor engine . sure looks like it.Here is why I am confused with your alls valve clearance specs. Makes it difficult in what to believe.
ooh wow i hit it on the head! see lack of info as usual.Ok ,maybe this is issue, iam working on m john deere. Not m IH. Can I get some feedback. Thanks
there is also a john deere site down below also. they are green tractors, farmall, ihc an mccormick are red tractors on this site.ooh wow i hit it on the head! see lack of info as usual.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy