Anonymous-0

Well-known Member
I'm supposed to be doing income tax so I am trying to avoid it for a while.

How long is the yellow lines on the HWY's

How tall is a standard ten gallon milk can with the lid off?

Can you cut off a flys head with a butter knife? a live one, no glue trap, no tricks?


How much weight can a single strand of baler twine--the old type hold? Like holding a cement block from a tree branch.

How much longer can I goof off before doing my tax preperation.....no forget that last one..


If you tip a full glass if water up against a unpainted cement block wall at five foot how many ounces of water will hit the floor?

If you twist a flat belt on a tractor of 50 hp, and hold it together in your hands can the tractor start the load? Like a WD 45- or a A JD, or a M Farmall.


All these questions may supprise you!
 
On rural two lane roads, yellow lines are the length of the no passing zone.

Baler twine, one end tied to branch - other tied to three hole brick, brick will slowly spin and twine will seperate and brick will fall to ground.

On flat belt - I think the answer is no. I think there's a pic somewhere on this site of someone demonstrating that scenario.

I hope you do well on your taxes.

Paul
 
NE IA
U.S. Federal standards, Canada similar.
Broken lane divider lines, yellow on two way, white on one way/divided roads- 10 foot line with 40 foot space, (10 feet on 50 foot centers). Yellow line is always on your left.
Short broken white line, 5 plus 20,(5 on 25 center) lane will end soon. Usually within 500 feet, such as exit only lane, or entrance/ acceleration lane.
Illegal to cross double solid yellow line except to turn left into driveway.
Illegal to cross DOUBLE solid white line. NOT illegal to cross SINGLE solid white or yellow line.
More than you wanted to know this early in the morning.
Willie J
 
Without measuring the milk can, I'd say no more than 20 inches. Depending how carefull you are, I don't think any water would reach the ground.
 
1. Can't measure the yellow line on my gravel road till the snow thaws.

2.I've never milked cows

3.Yes! Go to the hog house at night when the flys are stuck to the ceiling and cut away.

4.Wear steel toe shoes when trying this.

5. Do the tax prep the day before you see the tax man so you remember what you did to come up with those screwy figures.

6.Depends on how hard the wind is blowing.

7.How much do you value your hands?
 
Only one I can answer with certainty is the milk can question. I hauled can milk for two years,sold can milk a lot longer than that. A can is 24 inches tall. Anybody tells you different doesn't know what they're talking about.
 
I'm supposed to be doing income tax so I am trying to avoid it for a while.

Answer is. true


How long is the yellow lines on the HWY's

answer is most folks guess three to four foot. when we measured with a tape they were 18 ft. about ten years ago is the last time I measured

How tall is a standard ten gallon milk can with the lid off?

answer is most folks say thirty to thirty six inches. real answer is twenty four



Can you cut off a flys head with a butter knife? a live one, no glue trap, no tricks?

answer is yes, It works best when there is spilt food on a picknic table etc. and they are determined to be there. Take a butter knife at 90 degrees to their head / body, and the trick is to go rather slow and steady. I guess they see a fly in the reflection, and pay no attention. I have won many chocolate malts on that one.



How much weight can a single strand of baler twine--the old type hold? Like holding a cement block from a tree branch.

Answer is alot for a little while, then it starts spining from one way to the other and unwinds the string in less than ten munites.

How much longer can I goof off before doing my tax preperation.....no forget that last one..
Answer is the sherriff will explain it again this year, as well as the judge.

If you tip a full glass if water up against a unpainted cement block wall at five foot how many ounces of water will hit the floor?

Answer is not a drop, the block will suuuck it up.


If you twist a flat belt on a tractor of 50 hp, and hold it together in your hands can the tractor start the load? Like a WD 45- or a A JD, or a M Farmall.

Answer is no, my dad used to do this at silo filling time and the prowd neighbor with his new powerfull tractor. Straddle the belt at the crossing point, place your hands on both sides of the belt, and press your hands with your knees. You will burn a clutch out before starting the load.

All these questions may supprise you!

Hope some one found this ammusing on a cold winter day.
 
Well I am kind of confused on the milk cans then, I have 2 of them over at the farm that still have grandpas number painted on them, and they are both 32" tall with the lid on. How many gallon would these be if a 24" can is 10 gallons?
 
I would be willing to place on bet on the belt pulley one. A John Deere R is 49 horsepower, and I would bet there is no man out there that could do what you said and burn up the clutch on the R. Either the belt would slip on the pulley or the guy is gonna have some nasty burns on his hands. I am willing to bet with the ability to slowly engage the hand clutch and the torque of that diesel engine, the guy is gonna get toasted. Now granted this may not be true of every 50 horse tractor, but on a Deere with the pulley right on the crank, you are getting every drop of the horse it makes.
 
I would wonder how much you are willing to bet perhaps, but up to date I have never seen one that would. The only exception was when the guy at full trottle just dumped the clutch on a M IH. It caught dad off guard as he never thought anyone would abuse a tractor like that, but dad did in deed have it coming, because everyone was laughing at the M's owner.

I'm not here to create any troubles, but why not give it a try some time and see.
 
With this belt setup, are you talking about having the tractor belted up to something, and having a twist in the belt? Then a guy pinches the belt just before the twist, between his hands with pressure from his knees. I don't have anything here to belt up to but I sure would like to see someone try it with something like an R or a 70. It doesn't make sense that a tractor like that can take into a load like a 3 or 4 bottom plow in the ground but wouldn't be able to break the friction a guy put on the belt.
I am thinking with some of the other tractors that the belt is driven thru a bunch of gears, that you may be right. I just can't see that being a problem with a belt pulley on a Deere. I will have to see this spring if I can find someone around that I can borrow a belt driven implement for a few minutes.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top