STILL NO SPARK

JIM603

New User
NEED HELP ! HAVE A 1950 8N SIDE MOUNT DISTRIBUTOR. 6 VOLT POS. GROUND. WENT BY MY I.T. BOOK ON TIMING THE MOTOR. AND STILL NO SPARK. I HAVE CONSTENT POWER TO THE DISTRIBUTOR SIDE OF THE COIL. IT BLINKS BUT DOESN"T GO OUT. IS MY TIMING OFF OR ARE THE POINTS NOT SET RIGHT. PLEASE ADVISE. THANKS.
 
Jim.......surprizingly enuff, you should have blinkin' at the distributor points input. Yer timing is NOT OFF. Its yer points (0.025") they haffta OPEN to make sparkies. And they haffta CLOSE to make'um blink. Iff'n yer gittin' constant volts at the distributor input, yer coil to points wire is OPEN. .......Dell, yer self-appointed sparkie-meister
 
I assume that yoou set the points to 0.025" make sure they are making contact. if they are old points they may be corroded, if new they may have a coating on the and need to be cleaned. don't sand new ones just use a piece of brown paper and clamp it between the closed contacts. if they are old one, mighet be time to replace them.
 
Unless your points are new,you should get new ones.O"reilley"s has Borg-Warner points,cond,caps,etc.at $6.00+-,you can"t beat them.They are made in Mexico,but all of them are made somewhere,China,Taiwan,etc.I bought a set at CNH that were made in taiwan.They worked well,but I had to readjust after a while becauseof the rubbing block.---lha
 
First, please turn the caps lock off. It makes it hard to read on these old eyes!

Do you have voltage across the points when they are open? Verify the gap on the points at .025. Then, run a piece of card stock or brown paper bag through them. New points sometimes have a residue & old points can corrode, or get grease from the distributor cam on them. Or, you could have used a dirty feeler gauge. (I always spray mine off w/ contact cleaner.) Make sure you have voltage across the points, as in past the insulator on the side of the distributor. That is a very common failure point on sidemounts & often hard to find because it is usually an intermittent short. (If you find the short there, the Master Parts catalog lists everything you need on page 154. You can make the strip and you could also make the insulators as well. But, somethings are just easier & in the long run cheaper to buy. Get the strip, 12209, screw 350032-S, 12233 bushing & 12234 insulator & just replace it all.)If you just replaced the rotor & lost spark, put the old one back in. Check continuity on the secondary coil wire. Make sure it is firmly seated in both the cap & the coil. In fact, replace it temporarily w/ a plug wire.


Check the points for wear. Usually burned points will have pits on one side & raised areas on the others. Sometimes they just wear unevenly. They will most always discolor as they have a coating on the surface. The usual causes of burned points are absence of cam/wearing block lubricant, condenser failure, a decreasing gap caused by wear on the rubbing block, mis-alignment, sanding w/ a point file, excessive current, setting an incorrect gap, leaving the ignition key on w/ the points closed, use of incorrect cam lubricant & poor quality metal.

Quality parts are critical to longevity. Having learned the hard way, I most always use Blue Streak brand points. They are made by Standard parts & available at many auto parts stores. (frontmount points also fit a 48 Ford as I recall) Beware of sticker shock: $16-18 a set. My next choices are CNH, Wells or Echlin. Look for a brown rubbing block. Unfortunately, many folks have experienced problems w/ points made by Tisco, Sparex, A&I Products and any TSC ignition parts.

Correct points installation & gap is also important. Make sure the blade is at a perfect right angle to the points & you want to feel just the slightest bit of drag when you pull the blade through the points. Make sure the points align correctly.

Even as tight as I am, I always change the condenser when I change the points…….and then I toss the condenser in the “used” parts box. A bad condenser is rare; you can tell if the points are pitted/burned w/ metal transfer.

Good hold-down screws are important. (tip # 37) If the heads are wallowed out, what do you think the threads look like? You can use machine screws as temporary replacements, but you should use the OEM Fillister head screws. The larger head is there for a reason. If you do use standard machine screws, make sure they aren’t too long & interfere w/ the advance weights. Always use star washers under the screws.

Timing is important not only to engine performance but points longevity as well. Make sure you set the point gap before you set the timing. Timing a sidemount is pretty straight forward; it has marks on the flywheel. If the engine doesn't start, tell us how you set the timing.

Post back w/ results; I'll be interested in what the problem was.
50 Tips
 
Thanks guys will try as you suggested, will let you know how it goes, sorry Bruce for the cap lock. Bad habit i guess.
 
Retarded timing will make the engine run hotter, but I don't see how that could burn points. With retarded timing, the coil will be firing against less compression and consequently the coil will build up less voltage to fire the plug gap. An ignition scope will show a lower voltage spike on a weak cylinder.

When less secondary voltage is built up, there will be less voltage induced back into the primary with less ringing effect. If anything, I would expect retarded timing to slightly extend both point and coil life. Please explain your position.
 
Do you have a part or reference # for the Borg Warner points at O'Reilys? It always good to have a source for parts in stock vs mail order.
 
Hmmmmm.......my explanation is a lot simpler: I learned that 45+ years ago from an old mechanic, therefore, it must be true!

Once again, logic & analysis trumps a good story.
 
Do you think his insulation and copper strip might going into the dizzy might have grounded out? No spark there; it happened to me. Also, just asking, but is your Coil's positive stud on the dizzy side? Points plus positive +++.
 
(quoted from post at 13:39:16 07/12/10) Hmmmmm.......my explanation is a lot simpler: I learned that 45+ years ago from an old mechanic, therefore, it must be true!

Once again, logic & analysis trumps a good story.
Stuck response in wrong post! Well here it is anyway:

JMOR
Tractor Guru


Bruce, you just aren't much of a politician!
Any half wit bureaucrat would have either claimed "I mis-spoke" or that the recipient "mis-heard". :lol:
 
Here a thought, if my timimg is right and my points are off the mark,then if i install a Electronic Ignition kit in will my problem go away.
 
Jim......while the 5-nipple sidemount distributor has "better" 6v electronic ignition than the 4-nipple frontmount, its still a 6-volt cripple.

Make certain yer plastic insulation feed-thru and flat spring points connection are NOT shorting out. Converting will NOT fix shorts or opens. .......Dell, sparkie-meister
 
Huh? You'd rather spend $150 for EI than $15 for a set of points?

The EI debate comes up here w/ such frequency that you would benefit from doing an archives search on the topic. Generally speaking, you will find a few facts, a lot of opinion, & unfortunately, a little BS (“ my EI system doesn't have any transistors... “) . And sometimes you will find factual information that isn’t the least bit relevant to installing EI on a 23 hp, 60 year old tractor. (“the automotive industry went to EI 35 years ago”)

Suppose the problem is the insulator on the side of the distributor, as I've suggested & Dell has suggested? If that's the case, then you will have a tractor w/ EI that doesn't run instead of one w/ points that doesn't run.

Bottom line.....none of us can tell you what the problem is. We have all offered suggestions for you to find it. If you want to throw parts at it (and expensive ones at that) rather than troubleshoot the problem, at some point it will probably start before you run out of money.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top