Took Micrometer Apart

I took a moderate priced micrometer apart thinking it needed cleaning. It was off about .0003 before when closed, which was good enough for my work. Now it is .002 when closed. What did i do wrong. A good machinist told me I had ruined it when unscrewing it all the way. i suggested adjusting the anvil and he told me I had already ruined it. Any help?
 
Adjust it. Typically, there's a lockscrew in the thimble, allowing it to be set back to "zero".
 
Someone put it together didn't they? You should have a hook wrench to turn the barrel and line up the zero when closed. I sugest getting some gauge blocks and checking it through out it's range. Make sure the tips are clean and there is a feel for measuring with them or use ratchet.
Later Bob
 
Assuming you did not remove the anvil and that you unscrewed the thimble - Most O.D. mics are adjustable by turning the thimble sleeve using a small spanner wrench that should have came with the mic. Assuming you took it apart and handled it with care and only cleaned it with denatured alcohol (or similar)and a lint free cloth, no harm was done by taking it apart - as Bob said they are meant to be taken apart to clean and adjust. One other word of caution: nowadays just because one is a "good machinist" doesn't necessarily mean they know anything about the inner workings of gages and the like. I work with a few CNC Jockeys that call themselves "machinist".

landlord7012
 
go to its.fvtc.edu/machshop1/inspection/AdjustMic.htm or just google adjust a micrometer. You can read it easier than we can type it. HTH
 
Hey there moonlite;
Retired as millwright,I think your"good
machinist" should go back to school!Any
(or almost any),precision micrometer is
adjustable.As I have said before there
are very few "true mechanics"today they
are just parts changers.Bob
God Bless
 
All of them are adjustible. The thread is a special 1:40 if I remember. Look in your Machinery Handbook for instructions.
 
Most mics come from the factory +/- .0002-.0003 setting. You can hold them in your hand for a few minutes and body temp will change that tolerance.

Larry
 
You will need to get a standard to set it right. Most sets come with one but indivuals won,t A mike propoprty set will give you accurate measurements needed to do detailed work Most times once set are good for long peroid of time if not dropped etc. As far as being off .003 that is railroad standards ha If you know for sure what it is off you can allow for it in measurement
 
You may have something on the anvils. Take a piece of paper and clamp in in the mic. Pull the paper out and repeat a couple of times. If it's still off hold the mic up to the light and make sure you can't see any light through the anvils with them closed. If they are completely closed and it shows off you will have to adjust the barrel until you get zero again.

I would question any machinist who doesn't know how to re-set a micrometer. If you can't get it set right you can have it re-calibrated. There's someone in your area who does that I'm sure.

Are these digital mics?
 
Most micrometers are adjustable, I happen to have one junk one in my tool box that isn't though and it's off by .001" (one thousandth) It's a Lufkin, and it's probably 2x older than me but it came in a tool box I got from a past co-worker who picked it up at a rummage sale for me.

What brand is your mic? If it's a Starrett or a Mitutoyo, it's gonna be adjustable. Most others are as well, but some aren't. If you bought it new, it should have come with a wrench to adjust it, otherwise your buddy, if he knows anything about them (doesn't sound like it) and he has a set of his own mics, he should have a wrench to adjust his with. Might be the same one you need to adjust yours.

Follow the link that Little Ed posted. It's actually to the school I went to for the machine tool program and I graduated fomr there last May.

Donovan from Wisconsin
FVTC Adjusting a Micrometer
 
Thank You, I cleaned it well and oiled and now is .0025 when dully closed. i think it may have gotten bent as it turns a bit harder than it should. I am going to go to a machine shop and borrow a standar. I did measure the shank of a new twist drill and compared the reading with another micrometer I have. I can just subtract .002 from the reading. It is at least 25 years old as I used it when is school. And is an MG made in New York. It looks nice but is a moderate priced one. The other one is all beat up but reads good. I Used the beat up one for anout 14 years to measure sheet thickness. The beat up one has an adjustable anvil. I used to measure sheets and forget and carried in pockets or left on a desk top.
 
Just a thought here, but did you happen to touch the collar that"s under the thimble? If you moved that one way or the other, that affects the feel of the micrometer, making it tighter or looser to turn.

The best lubricant for micrometers and other measuring tools is either the oil that Starrett sells, or plain old WD-40. I clean mine off with electronics cleaner and then spray them down liberally once in a while.

Donovan from Wisconsin
spinutight.jpg
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top