Trailer Brakes

super99

Well-known Member
I have an older P&J gooseneck that I haul my 1550 on. A couple of weeks ago, I hauled the tractor to a ride 60 miles away. Evidently I didn't get the plug in far enough to catch the latch and it came out and when I arrived, all I had was a wire dragging on the ground. I borrowed a pickup and drove into town and got a new plug in for the trailer, came back and wired it up correctly and came home. I'm not sure, I don't think the brakes were working then. This afternoon, I hooked up the trailer and plugged it in and I don't get a light on the brake controller. I had my wife watch the light while I checked the plug with a test light. When I touch the tester to the brake prong, it lights up, so I think the wiring is good to the rear of the truck, all trailer lights work as should. I took the trailer plug apart and get nothing with the test light when the brakes are applied. It has to be something on the trailer causing the problem, correct?? I followed the wires under the trailer and all seems good. I took the cover off of the junction box on the trailer and tried the test light and got nothing on any of the studs. The only difference is I greased the ball on the truck before I hooked up the trailer. I thought that the trailer wiring had a ground included so the grease shouldn't make any difference should it?? I'm lost!!
 
The connector has a ground. All of them! The wire may have bounced around enough to fracture where it bent back touching the ground. I would make a bare section where the cable extends beyond that to the rear, and use a 12v source on each wire to see if they light lights and apply brakes. Don't check the ground with hot!
If the brakes work from there, do a waterproof splice with solder and shrink tube. Stagger the splices so they are not all in one spot!. Jim
 
If the trailer plug is wired to standard, the ground wire should be a white 10 or 12 gauge wire for a 7 flat blade plug. Brake wire should be a 12 gauge blue wire. If you have a break away switch, where is it wired into the brake circuit? Ahead of or after your test point? If ahead of your test point, it could have failed.
 
I just went out and checked it, the breakaway is after the plug in. I also took the ground wire
loose from the hitch and checked and cleaned it and put it back together, it looked good.
 
Look inside the plug again, I bet you got the brake wire in the wrong spot. There should be a ground in the plug and to the frame further back somewhere. Check those too.
I don't know if they are still done this way or not, but in the past the colors listed on the plug did not match the wire colors. I think on new plugs they don't list colors anymore but label them as to job done. So make sure that is correct.
 
7 way Traditional and RV Standard show the normal wire colors for the flat blade plugs (The 7 way heavy duty is the round pin plugs). You will note the colors change but the positions stay the same on both 7 flat blade plugs. One of these may help you determine the wires are on the right terminals to match what your truck should be wired to. (This is guessing you have a 7 flat blade plug on your gooseneck and truck.)
mvphoto79749.jpg
 
Everybody's favorite... Trailer wiring....

Since the only thing you changed is the end plug, the odds of it being something more distant are slim if everything worked before.

I'd start by verifying the continuity between the plug you replaced, and the junction box. Next would be continuity of ground between the truck, and trailer when plugged in, but not hitched. Obviously you need to confirm which wire goes to which contact as well.
 
Well, if you get power to the brake pin at the plug on the truck, but you don't get power to the brake pin at the junction box, the problem is between the junction box and the truck. Either the plug or the wire.
 
I use a bunggie cord as insurance to prevent my plug from falling out.
My brake controller shows a C when it sees brakes are connected. I keep one eye on the controller.
I feel for you. My biggest fear is my electric brakes won't work when I need them the most.
 
Super99,

Use a jumper cable set and clamp from truck to trailer in good ground spots. That'll tell you if it is a ground problem or not through the plug. Pretty simple, quick and cheap troubleshooting.

D.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top