welding galvanized metal

Anonymous-0

Well-known Member
Hey folks,
I know the story book says no, but I have a water tank that split at the seam and I can't afford to throw it away. Think if I do it outside and maybe wear a dust mask I can get it done? Leaking won't be a big deal as it's on top, just don't want any sharp edges and gaping holes.

Dave
 
I was told, and have done:
Outside with plenty of fresh air, even holding my breath when the smoke gets in my face. Wire brush as much as possible the galvanizing off the area to be welded--you'll get a better weld. I also heard drinking milk afterwards will help counter the toxic effect. I guess it is a carcinogen, and will make you sick as well. I've been able to avoid the sickness--but who knows, I could die tomorrow from cancer from it...

Just don't breath the smoke, and plenty of fresh air--never weld it inside somewhere, with no air circulation.
Hope that helps.
 
Oh--I also used a hood, instead of goggles, to help keep out of my face, and a fan, to help dissipate the smoke.
And the galvanzining will spatter quite a bit, if you don't get it removed from the area to be welded.
I am not recommending doing it--so proceed at your own risk. Just saying how I went about it after consulting a welding professional who is also a part-time welding instructor--it can be done.
 

Thanks! It's an old tank and I'll run a wire wheel over the area first.Not much on milk, but if I get it back together I'll have a couple beers.


Dave
 
work in a steel mill & weld galvanize strip all the time buff/ grind the zinc off the area to be welded ( at least 1/2" back from edge & weld normally a stick machine will burn through the zinc & weld it ok but a wire feed machine the zinc will clog the nozzle if you don"t grind it off first best to always grind off zinc & then rustproof the weld area after as once the zinc is ground / burnt off the area will corrode
bob
 
(quoted from post at 05:34:14 02/08/09) I thought they were soldered, could you do that?.

I don't think in this case. It's an old liquid fertilizer (sh!t) tank that is converted to a water tank for the pasture. I filled it to put out just before the temps dropped more than expected and it froze and busted the welded seam. Gotta use straps to suck it back together and weld. The solder may be a good idea for leaks afterwards.


Dave
 
A dust mask won't protect you from the fumes, they are made to keep particles out, you can still breath through them. or, [this is a better solution,] have a small fan blowing the fumes away from you.
 
WARNING ! One of the most miserable nights in my whole life was when the fumes worked out of my sinuses. Put me in the hospital.Nothing they could except keep flushing my eyes out. Felt exactly like someone kept throwing sand in my eyes. Maybe you don't like milk, but drink a big glass of it. The milk will coat your stomach and then you won't absorb the fumes.The other alternative would be a self contained air mask.
 
(quoted from post at 06:24:09 02/08/09) WARNING ! Felt exactly like someone kept throwing sand in my eyes. .

Went a weekend like that a couple of months ago from welding without a mask (long story) I will drink milk though and try it.


Dave
 
I've welded plenty of this, just use good welding practice - keep your head out of the fumes and gring the galvanised coating off the are to be welded. If you don't, it will pop and smoke a lot. Good venting. Not a big deal at all!
 
If you value our life and health throw the tank away. Your life and health is worth more than a old leaky thank. It may not kill you but you never know what it will do to your lungs. I mig welded on new metal back when they stared grinding up the whole car and making new steel out of them. I ended up with a 50% disablity from Metal Fume fever caused by the minute amounts of Cad & Chrome that was in the steel This is a fact that the insurance company fought and lost on. Steel was tested and it was there and the old lung still bother around different fumes. DO NOT DO IT.
gitrib
 
Boilermaker Mechanic for Chicago Bridge and Iron, years ago. Welded a lot of stainless, mild steel and galvanized materials. Galvanized welding produces a little different 'puddle'...you may want to practice on some scrap first. But, as others have said, the fumes are toxic and you definitely don't want to breath them. Do it outside with a fan blowing if there is no breeze. Full helmet, always.
 
Welding galvanized steel creates zinc oxide fumes. If these fumes are inhaled in sufficient quantity, a condition called "metal fume fever" can develop. This is the result of irritation of the airways and the release of damaged proteins into the blood provoking an immune reaction. Symptoms are much like the flu. It will not kill you but you may wish you were dead for 24 to 48 hours or so.

Milk will NOT prevent the condition from developing. (You aren't eating the zinc, you are inhaling it.) Milk may be helpful in settling the stomach and reducing the nausea that is one component of the fever.

Zinc is NOT a carcinogen. It is an essential nutrient. You can buy it in the vitamin section of any supermarket or pharmacy. You can spread zinc oxide on your lips and face to ward off high alpine sunburn. As with any substance, ingesting too much zinc can lead to high blood concentrations, which MAY contribute to some of the misery of metal fume fever. But the main cause of metal fume fever is irritation of the airways.

Metal fume fever can develop from other metals besides zinc. Some of these really are carcinogens and can cause lasting damage beyond the acute sickness. Chromium, lead, and beryllium are examples.

Do a google search on "metal fume fever" and read the material for yourself.
 
Take a side grinder to it. A wire brush doesn't get deep enough. V out the crack so you get good penetration. Grind along side about a half inch on each side. Even then, try to keep away from the fumes. I usually get a bad headache if I inhale too much.
 
I would either get something new, or try to use some pop rivets and epoxy. Welding galvanized is tough, welding sheet metal is difficult, welding old, galvanized sheet metal is a pia. One of my neighbors fixed a fertilizer tank with some of the bediner stuff in a can. Been good for 3 years now.
 
Have good ventilation and it can be welded. With a stick welder, use 6010 or 6011 rods to burn through the zinc. MIG will work but grind the area clean before any welding. Inhaling the fumes can cause Zinc chills. A respirator with a filter made for welding fumes would do a lot more than a dust mask. They aren't too expensive and will fit under a welding helmet. Dave
 
Stay away from the yellow smoke, Make sure you grind well and wide to remove galvanize coating.

My brother did have a very bad experience building a utility trailer awhile back and thought he was dieing they called it galvanize poisoning. had too much in his lungs.

Didn't bother him at all till that night, then got deathly sick.
 
Vinegar used to remove galvanizing. Made cheap patch panels for cars long time ago. Make that vinegar and elbow grease or steel wool. Dave
 
I think Lincoln actually makes an innershield(flux-core) wire for galvanized metal. I don't know what kind of welder he has though. Dave
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top