What happened to this engine?

This is on a trencher, its a VG4D V4 wisconsin. It ran fine and I put the trencher back on the machine and went to try it. I got it at auction in pieces so I put it back together.

When the trencher was digging the engine started to squeal. I got it apart and found #4, the one with the discolored valve had a tore up connecting rod bearing and the cylinder is scored and the piston if tore up. It always had oil pressure. #2, the one next to #4 had a little wear on the clyinder and bearing. 1 and 3 on the other side of the engine are in real good shape. Any ideas what caused this?

https://photos.yesterdaystractors.com/gallery/trouble/r5199.jpg
r5199.jpg
 
I'm guessing but the exhaust valve on the left cylinder in the picture looks a bit oxidized like it has been running hot. Overly lean mixture? Poor cooling? both?
 
These are air cooled, as soon as I got it home I pulled the skins off the engine and cleaned all the fins.

I dont think it ran lean, if anything it ran rich.
 
Carbon would be my guess. Fouled rings causing the bearing to work harder. The discolored valve throws me. Would/could an exhaust leak contribute to it? I have seen small engines with rotted out mufflers do that....
 
Even though the engine has an oil pump, it is NOT "pressure oiled" in the traditional sense.

Rather than the crankshaft being "rifle drilled" for oiling the rod bearings with pressurized oil from the main bearings, the rod bearings (and cylinder walls) are oiled by oil squirted at them by a nozzle in line with them fed from the oil gallery.

I'd take a good look to see if the nozzle for the rod/cylinder that blew up is plugged.
 
Was the engine running & firing right? If the plug wires on 1&3 were switched , it would overload 2&4. No mouse nests??
 
When I got this it was probably setting for 5 year. I know it seemed to get hot fast. Just fireing it up for a minute you could see the heat comming off it. Im sure the fireing order was right, the distributer cap is numbered and the engine is numbered.

There was mice nests in it when I got is but I pulled all the sheet metal off and cleaned it out. I heard they overheat when not clean.

If the spark timing was off would that cause it to overheat? Ill try to see if the little oil tube is plugged up.
 
If the exhaust was able to get water in it,or there was some way it got moisture in that cylinder when it sat,and then you started running it,all of that rust and crud could have scored that cylinder then caused the rod bearing to fail.When you turn a motor off many times it will stop in the same place.Thats why if you have teeth off of your fly wheel,it usually wont crank without turning the motor a little off of the bad place because it stops there almost always.If it sat for 5 years before you ran it,it could have sat many times before and that same cylinder was exposed to water,rust,crud until it ruined it.If water could get in the exhaust,one of the cylinders,number 4 in your case had open valves,or the way it sat was the lowest and had open valves and water got in the combustion chamber and rusted it.Another thing could have been the crud broke a ring,or the motor had a broken ring when whoever quit using it.Maybe carbon built up from burning oil or a bad valve guide letting oil in carboned up the top of the piston breaking a ring ruining that cylinder.
 
When I got it the engine was in a barn and the carburator and exhaust were blocked off with plastic and tape. I have no idea what happened before that.

I dont think any rings on #4 are broke but Ill go look.
 
#4 running VERY lean is my guess. A bad intake gasket or leak pulling in outside air would cause it to do this. Once the piston started to score, that could possibly explain the excess load on the crank.
 
a lube squirter nozzle for the piston clogged up and took out the piston. don't know about the valve. Maybe not enough lube? We used to put some oil in the gas to keep valves from sticking.
 
Don't put your danmed engine pictures in STUCK AND TROUBLED TRACTORS section. Put them in parts and pieces where they belong! I can't believe how some people can't read.
Sheesh!
 
I just met a guy today at a swap meet that said that he has some NOS Wisconsin parts including rods on hand. I am looking for a used head but he didn't have one. He is located in Wisconsin and I have his phone number if you are interested.
 
Other things might be something broke on the side of the piston,some dirt or something got in that cylinder.Something could have been wrong when they quit using it.Maybe it got too hot or lost oil to that piston like somebody else said?If it was getting a lot of oil in there it might run hotter causing trouble.Usually if there is a scored place there is more wrong with the piston,rings,or something.
 
Today I poked a wire in those little tubes that spray oil on the connecting rods. Two of them seem to be plugged up. I guess thats what tore it up. What would cause them to plug, shouldnt the filter catch anything?
 
The way it sounds you ought to take it some where and get it cleaned real good,check the valve guides and grind the valves,whatever else it needs,then it might last.Oil that sets in a motor 5 years breaks down.If you didnt wash it out or something before you ran it,that broke down stuff is maybe what plugged everything up.Now you have to get it all out or keep on having trouble.
 
When I first got it I broke the drain pipe on the oil pan so I pulled the pan off and cleaned everything out. The oil that was in it looked brand new.
 
Might not be as bad as I imagined.I had a 390 Ford motor one time that sat outside for 3 years.When I took the pan off there was some gray looking stuff inside.An old mechanic said it was oil that broke down.The more I tore it apart the more of it I found inside of the bearings and everywhere.That was back in the 1970s.Probably straight 30 weight.
 
I had some grey junk to but not alot. Maybe when I have it tore down I could run some paint thinner through it or something to eat any junk up. When its fixed it will get synthetic.
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top