-
R
Red 56 Binder StuartIowa Red 56 Binder wrote on StuartIowa's profile.
How did you come out on the disk ?
Hey Jon, I saw on a post in May, that you are looking for a pair of side shields. I do have a pair. If you send me your phone number I can send pictures. The best part about this, is, I'm just down I-35 west of Des Moines a bit. So not too far from you. gobble Tom Hagen
Hello looking for assistance on an independent PTO CABLE.
Tractor : Ford 4000
Transmission : Select Zero Speed, 10 forward 2 reverse
Issue: PTO shaft does not disengage when T-Handle is pushed in.
Looking for info to troubleshoot PTO Cable Assembly, and subsequent parts down the line.
Looking for a good manual discussing the independent PTO assembly and setup & troubleshooting .
Any help would be appreciated.
Tractor : Ford 4000
Transmission : Select Zero Speed, 10 forward 2 reverse
Issue: PTO shaft does not disengage when T-Handle is pushed in.
Looking for info to troubleshoot PTO Cable Assembly, and subsequent parts down the line.
Looking for a good manual discussing the independent PTO assembly and setup & troubleshooting .
Any help would be appreciated.
I saw you had a problem with tractor stuck in reverse. What solution did you come up with to free it up? Mine is a Massey ferguson to-35. 1955 or 56 I think. worked great when parked. A couple months it set while I had surgeries. Started right up up shifter won't move and stuck in reverse. Can't find any information on this.
-
M
Martin Seebach flying belgian Martin Seebach wrote on flying belgian's profile.
If same engines probably will. If engines are only a few years apart and same specs, probably will. Our loader/scraper JD 300 Industrial has same engine as swather, 1.8l 4 cylinder and I stole the fuel pump from baler (NH) with same mounting holes and mating shape as tractor, works fine. Living in Brussels was a wonderful. So how are the banking characteristic on le Tracteur Aeroporte
I have a 53 ford golden jubilee. I replaced the rear wheel bearing and 1 axle. When I torque the bearing holder for lack of a better term the axles turn the same way. I have 4 shims on one side and 3 on the other. Of I loosen the bolts just a little the axles turn opposite. Should I use more shims or do I maybe have something else going on? The bearings and races are all in all the way.
I am married 62. I am just learning about older tractors. It is great my wife supports me in my endeavors. I do have a 1951 Case VAC 5555045. It has been a struggle to get it to run properly. I think I am close. I am up to running with sparks and flames out the exhaust??
I would like to register my Farmall cub. S/N=214284 J
Have a Hahn eclipse rototiller , engine model 100992 , 4 hp B&S on it, looking for a manual to identify carb number. Any help or direction appreciated
-
J
Joe Bolt NormanSavesTractors Joe Bolt wrote on NormanSavesTractors's profile.
Norman glad to have you here I have rebuilt a few k532 engines with your parts over the last 4 years. Now I am working on a M16 Kohler and I am wanting to know if the third balancer gear is to be positioned identically with the others or 180* opposite. The manual says position it parallel to the other two gears?
It is with deep sadness that I share an update on SWEDE in Iowa's behalf. On 07-07-2025, we lost our beloved dad, husband and grandpa to a sudden cardiac event. He spoke fondly of this group and enjoyed sharing tractor knowledge here. For any unfinished correspondence, please reach his son Andy at
[email protected]
Thank you and God bless.
From Lisa
FLY HIGH RON!
[email protected]
Thank you and God bless.
From Lisa
FLY HIGH RON!
I need help with determining if a wobble box on a nh 479 is the reason for destroying the cutting bar bushing or is something else the problem
-
P
Pafarmer1 jt candycane Pafarmer1 wrote on jt candycane's profile.
Re: the combine you inquired about, make me an offer. Canvas was kept in a heated garage. Where r you located? My cell is 814-229-4344 to talk details.
About 80 years ago, while I was in school and could not get to watch, my father and someone skilled, dynamited the top of a rock that would snag the plow. He hauled the pieces away and it never bothered the tillage since. How, I asked and said they covered the rock and dynamite with soft mud, then blew it. My question,,,,is that how you fracture the rock or was he jivven me?
-
C
cecrouser bamahunter cecrouser wrote on bamahunter's profile.
Did you ever find out why your transmission light was coming on? I have the same problem.
-
F
flmeredith casecollectorsc flmeredith wrote on casecollectorsc's profile.
sell the LA in the background ?
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy