(800) 853-2651
SHOP NOW

New profile posts

Yesterday's Tractor Forums
What's new Featured content New posts New media New media comments New resources New profile posts Latest activity
A
Hi Mike, I had read a previous post from a few years back on a 1209 JD mower conditioner. I believe you mentioned you had a copy of the technical manual. Would you be able to email that to me? My email is moline at woodstocktel.net
I am mainly looking at replacement of the rubber roller bearing replacement on the right hand side, just behind the small drive sprocket. Thank you very much.

Attachments

  • JD 1209 RH 2.JPG
    JD 1209 RH 2.JPG
    246.6 KB · Views: 0
RedWhiteandBlueWoods
Have had the Super C torn apart for awhile. The rod journals checked out with the dial caliper. Still have to get the rear main seal off and get the crank out. Have to clean out the transmission bellhousing, might need a new input shaft, shes pretty shredded either from whoever put the combine engine in or just wear and tear. Main bearings are smoked though.
T
Hey Jon, I saw on a post in May, that you are looking for a pair of side shields. I do have a pair. If you send me your phone number I can send pictures. The best part about this, is, I'm just down I-35 west of Des Moines a bit. So not too far from you. gobble Tom Hagen
B
Hello looking for assistance on an independent PTO CABLE.
Tractor : Ford 4000
Transmission : Select Zero Speed, 10 forward 2 reverse
Issue: PTO shaft does not disengage when T-Handle is pushed in.
Looking for info to troubleshoot PTO Cable Assembly, and subsequent parts down the line.
Looking for a good manual discussing the independent PTO assembly and setup & troubleshooting .
Any help would be appreciated.
Hayman101
Deciding to sell my Case International 435 Square baler. Selling for $3,000

Attachments

  • Case 435.jpg
    Case 435.jpg
    124.2 KB · Views: 1
M
I saw you had a problem with tractor stuck in reverse. What solution did you come up with to free it up? Mine is a Massey ferguson to-35. 1955 or 56 I think. worked great when parked. A couple months it set while I had surgeries. Started right up up shifter won't move and stuck in reverse. Can't find any information on this.
M
If same engines probably will. If engines are only a few years apart and same specs, probably will. Our loader/scraper JD 300 Industrial has same engine as swather, 1.8l 4 cylinder and I stole the fuel pump from baler (NH) with same mounting holes and mating shape as tractor, works fine. Living in Brussels was a wonderful. So how are the banking characteristic on le Tracteur Aeroporte
S
I have a 53 ford golden jubilee. I replaced the rear wheel bearing and 1 axle. When I torque the bearing holder for lack of a better term the axles turn the same way. I have 4 shims on one side and 3 on the other. Of I loosen the bolts just a little the axles turn opposite. Should I use more shims or do I maybe have something else going on? The bearings and races are all in all the way.
Ron Case VAC
I am married 62. I am just learning about older tractors. It is great my wife supports me in my endeavors. I do have a 1951 Case VAC 5555045. It has been a struggle to get it to run properly. I think I am close. I am up to running with sparks and flames out the exhaust??
NormanSavesTractors
NormanSavesTractors
Hi Ron! Welcome to the YT forum. You may want to check out your valve train. But post your question in the Case Tractor Forum and our members here can help you narrow it down
R
Have a Hahn eclipse rototiller , engine model 100992 , 4 hp B&S on it, looking for a manual to identify carb number. Any help or direction appreciated
B
Hello, looking for assistance on a Ford select zero speed, 4000 3 cylinder diesel that has a PTO engaged, is not disengaging.
B
BM7
Hello, looking for assistance on a Ford SOS 4000 3 cylinder diesel that has a PTO engaged. The T-handle has threads that are not great to thread to the conduit tube.
Also the cable is not disengaging the PTO ( is an issue there ).
Looking for info to resolve the PTO as is engaged.
I do need a new T-Handle on dash.
Need info on cable ( if needs replacing and set up )
J
Norman glad to have you here I have rebuilt a few k532 engines with your parts over the last 4 years. Now I am working on a M16 Kohler and I am wanting to know if the third balancer gear is to be positioned identically with the others or 180* opposite. The manual says position it parallel to the other two gears?
NormanSavesTractors
NormanSavesTractors
Hi Joe! Thanks for the message I got your email just now too. I am going to email you the kohler service bulletin with instructions for the 3 balance gear set up.. They essentially install so all the heavy side of the balance gears are 180 oppose the counter weight of the crankshaft. I will send that email to you now.
S
It is with deep sadness that I share an update on SWEDE in Iowa's behalf. On 07-07-2025, we lost our beloved dad, husband and grandpa to a sudden cardiac event. He spoke fondly of this group and enjoyed sharing tractor knowledge here. For any unfinished correspondence, please reach his son Andy at
[email protected]
Thank you and God bless.
From Lisa
FLY HIGH RON!
1
I need help with determining if a wobble box on a nh 479 is the reason for destroying the cutting bar bushing or is something else the problem
P
Re: the combine you inquired about, make me an offer. Canvas was kept in a heated garage. Where r you located? My cell is 814-229-4344 to talk details.
I
About 80 years ago, while I was in school and could not get to watch, my father and someone skilled, dynamited the top of a rock that would snag the plow. He hauled the pieces away and it never bothered the tillage since. How, I asked and said they covered the rock and dynamite with soft mud, then blew it. My question,,,,is that how you fracture the rock or was he jivven me?
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top