(800) 853-2651
SHOP NOW

New profile posts

Yesterday's Tractor Forums
What's new Featured content New posts New media New media comments New resources New profile posts Latest activity
M
I’m building a Minnieoplia moline U pulling tractor. I’ll pull in the 5000 to 6500 pound classes and was wondering what size rear tires people might think that works best.
View previous comments…
M
MinnieU44
I got the tractor with 11.2x34 im trying figure out if it should do 14.9x38 or bigger tire
M
MinnieU44
I’m pretty sure it is a 10 rim but I know I’ll have to get bigger rims to upsize the tire
D
DeltaRed
18.4 34 would be good.
L
1893 Case Shaft Driven Threshing Machine. 12 Horse Sweep Power with all accessories. Good Condition
16834.jpeg
RedWhiteandBlueWoods
Popped the crank out the other day, that last main cap was in there hard. Last main wasnt nearly as bad as the other two. Now I just need to get the block and crank down to the engine guy to get the block boiled and ask for bearing specs and a polish.
A
Hi Mike, I had read a previous post from a few years back on a 1209 JD mower conditioner. I believe you mentioned you had a copy of the technical manual. Would you be able to email that to me? My email is moline at woodstocktel.net
I am mainly looking at replacement of the rubber roller bearing replacement on the right hand side, just behind the small drive sprocket. Thank you very much.

Attachments

  • JD 1209 RH 2.JPG
    JD 1209 RH 2.JPG
    246.6 KB · Views: 0
RedWhiteandBlueWoods
Have had the Super C torn apart for awhile. The rod journals checked out with the dial caliper. Still have to get the rear main seal off and get the crank out. Have to clean out the transmission bellhousing, might need a new input shaft, shes pretty shredded either from whoever put the combine engine in or just wear and tear. Main bearings are smoked though.
T
Hey Jon, I saw on a post in May, that you are looking for a pair of side shields. I do have a pair. If you send me your phone number I can send pictures. The best part about this, is, I'm just down I-35 west of Des Moines a bit. So not too far from you. gobble Tom Hagen
B
Hello looking for assistance on an independent PTO CABLE.
Tractor : Ford 4000
Transmission : Select Zero Speed, 10 forward 2 reverse
Issue: PTO shaft does not disengage when T-Handle is pushed in.
Looking for info to troubleshoot PTO Cable Assembly, and subsequent parts down the line.
Looking for a good manual discussing the independent PTO assembly and setup & troubleshooting .
Any help would be appreciated.
Hayman101
Deciding to sell my Case International 435 Square baler. Selling for $3,000

Attachments

  • Case 435.jpg
    Case 435.jpg
    124.2 KB · Views: 1
M
I saw you had a problem with tractor stuck in reverse. What solution did you come up with to free it up? Mine is a Massey ferguson to-35. 1955 or 56 I think. worked great when parked. A couple months it set while I had surgeries. Started right up up shifter won't move and stuck in reverse. Can't find any information on this.
M
If same engines probably will. If engines are only a few years apart and same specs, probably will. Our loader/scraper JD 300 Industrial has same engine as swather, 1.8l 4 cylinder and I stole the fuel pump from baler (NH) with same mounting holes and mating shape as tractor, works fine. Living in Brussels was a wonderful. So how are the banking characteristic on le Tracteur Aeroporte
S
I have a 53 ford golden jubilee. I replaced the rear wheel bearing and 1 axle. When I torque the bearing holder for lack of a better term the axles turn the same way. I have 4 shims on one side and 3 on the other. Of I loosen the bolts just a little the axles turn opposite. Should I use more shims or do I maybe have something else going on? The bearings and races are all in all the way.
Ron Case VAC
I am married 62. I am just learning about older tractors. It is great my wife supports me in my endeavors. I do have a 1951 Case VAC 5555045. It has been a struggle to get it to run properly. I think I am close. I am up to running with sparks and flames out the exhaust??
NormanSavesTractors
NormanSavesTractors
Hi Ron! Welcome to the YT forum. You may want to check out your valve train. But post your question in the Case Tractor Forum and our members here can help you narrow it down
R
Have a Hahn eclipse rototiller , engine model 100992 , 4 hp B&S on it, looking for a manual to identify carb number. Any help or direction appreciated
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top