(800) 853-2651
SHOP NOW

Recent content by 2 color green

Yesterday's Tractor Forums
  1. 2

    What's it worth--- 310 diesel motor

    Figure out what you want. I might be intertested.
  2. 2

    running backward diesel jd

    There is no way to keep the 2cyls from running backward. Be ready to decopress the second it stalls.
  3. 2

    fuel filter

    Sorry. A little stupid!! 435
  4. 2

    fuel filter

    The fuel filter is no longer available from Deere. Is there another source, & if not, what type filter assemblies are being used?
  5. 2

    Dealer invoice question

    Invoice price is accurate. This is exactly what the dealer has to pay for the car, but there is a thing called holdback. This is money the manufacturer will pay to the dealer. On most new cars today, that amount is 5% of sticker. If car sticker is $30,000.00, the holdback is $1500.00. This is...
  6. 2

    John Deere reduction gear swap.

    I know of a tractor that has it done. The owner said it took a lot of work.
  7. 2

    15.5 VS. 16.9

    If you are getting a lot of black smoke, you aren't getting enough air. I have a 70 with 80 plus HP & very little smoke.
  8. 2

    JD 70 diesel first reduction gears into a G

    It can be done, but a lot of machining.
  9. 2

    how to get more rpms out of a oliver 88 diesel

    How much RPM are you looking for?
  10. 2

    Oliver 99 GM Pull

    Somebody posted about a Oliver 99 GM pull, I think in Ohio. What is the date, location, etc. Any info would be appreciated.
  11. 2

    Things that make you go hummmmm.

    Kruse had the same issues back in the late 70's, early 80's. Sold vehicles, collected money, didn't pay seller. Nice bunch!
  12. 2

    Overhaul

    Have a new 1010 rear. Would like 60HP neighborhood. Know about parts availability, just looking for someone to do the work. I really want the governor to react faster than they normally do. I have see a couple of them pull that when you touched the throttle, they reacted immediately. Thanks for...
  13. 2

    Overhaul

    Looking for somebody in Michigan to overhaul 2-53. Want to get some HP. Any suggestions?
  14. 2

    PTO Shaft

    The engine will bolt right in, no modification necessary, & the drive shaft needs to be shortened, which I have done. My only issue is PTO shaft. I will use the 77.
  15. 2

    PTO Shaft

    Installing a 88 engine in a Super77 chassis. I have the clutch shaft shortened, do I use the PTO shaft from the 88?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top