(800) 853-2651
SHOP NOW

Recent content by AJK

Yesterday's Tractor Forums
  1. D

    OT- I was only going 20 he said...

    On our way home last night, we came upon a car that lost it in the roundabout that was iced up, and a bunch of other passer-by's had stopped to lend a hand. I figured since it was Christmas I'd stop as well to see if one more guy would be able to get it out of the snow. We tried, but that car...
  2. J

    41 and newer chevy truck frames

    I know that 41 through 46 chevy pickup bodies are similar. Does anyone know if a 41 frame is the same as a 47 to 54? I need a frame for my 41 pickup and I have the access to many 47 to 54 trucks but I'm not certain they will work. Any help would be most appreciated. JRCustom
  3. S

    730 gas vs diesel

    Does anyone have one of each to compare? Looking for feedback about the differences between the two (aside from the obvious fuel consumption difference). Although they're both the same HP, is there a noticable difference in torque or "down to the last breath" lugging ability? How about noise...
  4. A

    '96 newholland 1920

    I have to rebuild the gland nut on the power steering cylinder ( seal and wiper) and I've never done it. I have the cylinder apart and the nut removed from the shaft. They appear to be pressed in. I'm waiting for the parts in the mail. Any Help?
  5. A

    Driving Out a Track Pin

    Go to the link below for a picture of an easily made tool for knocking out m/pins, a few bits of slotted bar,piece of pipe and a piece of heavy bar that is just a little smaller than the pin, AJ Master Pin Punch Holder
  6. A

    1954 TD9 steering clutches.

    I would just emery paper to clean them though they may be hard enough for sandblasting,test one,I do not know the stack height but you might find it at the link below. AJ TD9 Clutch Discs
  7. A

    D2 steering clutch

    Some people tie the lever back and run the machine into a solid object to try to break them free,other people soak the clutch in diesel but after spending nearly 55 years battling to keep oil off brakes and clutches it against the grain for me to recommend it. AJ
  8. A

    Komatsu D21A lift pump

    May not be the lift pump,take the line off at the lift pump from the tank,some of the Komatsu fuel joints that use a banjo fitting often have a gauze filter inside the bolt,when you remove the pipe check the flow as you can have trash in the tank,if your flow is ok to the L/pump and you have...
  9. A

    case 188 sleeves

    The 188 has wet liners and they should come out fairly easy,make sure all the coolant is out of the block,blow it out with air if you got it,take off the caps and wrap some cloth around the big end and shaft to keep the debris at bay,get a suitable length of bar and a bottle jack,put the bar up...
  10. A

    How come most part numbers don't match?

    Another link AJ Collins case
  11. A

    How come most part numbers don't match?

    Looking through the part # on the Case site there is no # like the one you are quoting 99% of the # have a prefix letter,the # on the housing may be casting #s and not part #s, doing a search for Case final drive turned this firm up. Component Services Inc Tel (877) 274 7278 or (317) 501 3766...
  12. A

    Still searching for a final drive

    There is a Case parts look-up online,its at the link below,when the first page opens click on Click here to begin your search,another page opens,in the top left corner type in 450,several options will appear,scrolll down and click on the first 450,then on figure listing,go down to transmission...
  13. A

    Case 480E backhoe question.

    Make sure that all the cables have good clean connections esp the battery box to the main frame,if no joy take the starter off and take it to the repair shop where they can test the speed and torque of the motor,I have come across starters that were turning slow due to water getting in from...
  14. A

    580 b case backhoe problem(lever that holds hoe up)

    I would be looking for excessive play in the pins around the swing tower,something may be worn allowing the hoe to jump about,does the boom clyinder hold up with a load,if it dropping all the weight would be on the latch when in transport mode. AJ
  15. A

    D239 timing question

    If you got a Bosch injector pump a special adaptor and dial gauge is screwed into the back of the pump to check/set the static timing,doubt if it out unless you altered it during the overhaul,the best site for IH info is Redpower at the link below,you will need to register to post on that...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top