(800) 853-2651
SHOP NOW

Recent content by Bakraz

Yesterday's Tractor Forums
  1. B

    New Idea 30 B sickle mower

    I recently purchased a New Idea 30B sickle mower and want to change all of the fluids. The Operating Manual shows adding gear oil to the ratchet gear case and there is a drain plug right below the ratchet gear case, There is also a second drain plug below the lift mechanism, but no mention...
  2. B

    Welder Plug Question

    Under certain circumstances a 50 amp breaker can be used to feed 30 amp wire (10 gage) for a dedicated welder outlet depending on the duty cycle of the welder. See National Electric Code Article 630 (2008 ed.)
  3. B

    Welder Plug Question

    The plug is rated for 50 amps. The receptacle is rated for 30 amps. I would check your welder's input requirements and compare it with the size of the breaker and wire feeding the receptacle. Your welder will probably work on this receptacle but you may not be able to use the full capacity of...
  4. B

    JD 3010 Gas Engine Noise

    Thanks for the input. Unfortunately since I do not own the tractor I am unable to diagnose per your suggestions. I am thinking that it may be a well worn engine balancer causing the noise. I think I will pass on this tractor.
  5. B

    JD 3010 Gas Engine Noise

    I am looking to purchase a JD 3010 Gas tractor that has a fairly loud rubbing/scrapping noise near the front of the engine. At first I thought it was a bad bearing on the alternator (the alternator belt had a sight wobble to it). After further inspection I have concluded that the noise is...
  6. B

    Oliver 77 Engine Removal

    Thanks for the follow up. After looking at my engine again I see what you are saying. Great tip on Fastenal. Store was less than 3 mi. from me and I didn't even know it existed! Very interesting store. Thanks again.
  7. B

    Oliver 77 Engine Removal

    Thank you for your reply. Am I correct in my understanding that by "lifting head bolt" you are referring to the threaded head studs that extend above the head about 2 inches? If so, they are located on the left side of the head and would seem to cause the engine weight to be unevenly distributed...
  8. B

    Oliver 77 Engine Removal

    Please just assume that I wish to remove the engine.
  9. B

    Oliver 77 Engine Removal

    I need to replace a broken shifter rail which requires removal of the shifter rail cover which requires removal of the belt drive which requires removal of the engine.
  10. B

    Oliver 77 Engine Removal

    I have an Oliver 77 Row Crop that I need to remove the engine in order to do some transmission repair. What is the best way to attach the engine to the hoist? Thanks in advance.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top