(800) 853-2651
SHOP NOW

Recent content by Bergmann

Yesterday's Tractor Forums
  1. B

    D14 venturi

    I replaced the plastic venturi that came with the carb rebuild kit with a metal venturi during my carb rebuild in a 1957 D14, which made a difference. I paid a premium. If you struggle with performance, you may want to look into the different venturi styles available for this carburetor. Carbs...
  2. B

    John Deere 855 - Air Intake System Question

    Excellent information, thank you Jim. This is very helpful. I'm grateful for the information and support. Have a good one!
  3. B

    John Deere 855 - Air Intake System Question

    Wore Out, thank you very much for the reply and sharing the link. That makes sense. Much appreciated! -Tom
  4. B

    John Deere 855 - Air Intake System Question

    Hi All, I recently purchased a John Deere 855. In doing maintenance to the air filter and eventually cleaning the radiator, I noticed that there appears to be an opening on the air intake canister and I haven't yet figured out what is supposed to cover it or connect it to. (bottom left is open)...
  5. B

    JD 2040 - Starter / Electrical Issue

    Thanks Tx Jim, will do! The price was almost too good on the starter... but I think you are right. More to come from this end.
  6. B

    JD 2040 - Starter / Electrical Issue

    Thanks for the reply, wore out. I was suspecting the solenoid the new starter came with may have been faulty originally. Rodent activity is unlikely, but it is possible, as it's in an enclosed shop with no known rodent activity. I think the wiring at the alternator is the most likely culprit. I...
  7. B

    JD 2040 - Starter / Electrical Issue

    Thanks for the reply, matthies, you could be onto something here. I did notice the alternator was vibrating quite bad when running. I removed the bracket holding the alternator to the block, long bolt that the alternator pivots on, and loosened the bolt/nut that slides for belt tension.
  8. B

    JD 2040 - Starter / Electrical Issue

    This post was edited by Bergmann on 12/26/2023 at 02:03 pm.
  9. B

    JD 2040 - Starter / Electrical Issue

    Thanks for the reply, used red MN. The machine has been sitting in an enclosed shop for the past 2 months. Before that, it was under a pole shed, exposed to the outdoors. Rodent activity is possible, but it isn't prevalent as we have 4 outdoor cats... I will investigate closer tonight and report...
  10. B

    JD 2040 - Starter / Electrical Issue

    Hi All, I welcome your thoughts and expertise with this. I recently replaced my 1979 John Deere 2040 starter. I pulled the Bosch starter out of it and found an off brand starter online for $120 that replaced the Bosch starter. I figured I'd gamble, as the name brand replacement appeared to be...
  11. B

    Allis Chalmers B carburetor question

    I experienced similar behavior in a slightly different Marvel Schebler carb rebuild and I believe replacing the plastic venturi that came with the carb rebuild kit with a metal venturi made the difference. I paid a premium. If you continue to struggle with performance, you may want to look into...
  12. B

    Seat for D series

    If it's comfortable, fits, and works for your needs, I support it. I unfortunately do not have experience with this particular seat model, but I like the idea. If you end up going with it, I would be interested to know how it turns out.
  13. B

    Trip Loader Question

    Joe M, Thank you very much for sharing. This is very helpful. You have a great looking tractor and I see the similarities in the loader type. That brochure is great too. I suspect you are correct. Upon looking a bit closer at the bucket, I found (3) sets of (2) holes that a bolt would go through...
  14. B

    Trip Loader Question

    I should have noted, the bucket tilted backwards when the pin is pulled even with the strut on the side. I added the strut so the operator could use it as a handle to dump the bucket. I have since removed the orange strap.
  15. B

    Trip Loader Question

    Hi Jim, Thanks for the response. These pictures aren't the best, but hopefully you'll be able to see enough of what i have going on. I do think you are right - more weight in the front could work. With how hard it currently is to pull the pin back to allow the bucket to swing and then push the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top