(800) 853-2651
SHOP NOW

Recent content by bowhunternw

Yesterday's Tractor Forums
  1. B

    Drilling Safety Valve Orifice

    Well i got it back together and nothing changed it still seems like it is cycling the hydraulics. I could see bubbles coming out the side of the block by the 3 pt lever. Like it was releasing pressure through the side plate
  2. B

    Drilling Safety Valve Orifice

    It is a 300. Maybe I will go look tomorrow for one just a hair smaller, just so it doesn't get too big.
  3. B

    Drilling Safety Valve Orifice

    So I got around to removing the orifice screw with the screen. It says 24 on it, the hole is about the size of a pin. From what I understand it should be a .03" hole. I have a 1/32" bit which would be about .03". This would end up being about twice the size as the pin hole it has now. Am I...
  4. B

    300 Utility Rims

    Does anyone know if the rear rims off a 8N would fit a 300 utility? Both are 28" and 8 lugs. I thought I had read somewhere that they would be interchangeable but don't want to buy if they wont fit. Thanks
  5. B

    300 utility hydrualics

    Do you have to drain the hydraulic fluid reservoir?
  6. B

    300 utility hydrualics

    Thankyou very much, is it located under the side cover or the end cover?
  7. B

    300 utility hydrualics

    I will check that out. I did try to do some searching and came across a topic that said to check the pressure relief valve. That a hole or screen can be plugged. Any idea where that would be located? The case ih parts website is currently not working.
  8. B

    300 utility hydrualics

    I have a 300 utility. I have most things operating the way I want now. However I do have this problem where it seems like the hydraulic pump works the engine while not operating the hydraulics. So describe this a little better. When I start the engine it seems to pulsate loading the engine, now...
  9. B

    Dearborn Shank Conversion

    Yes that would work perfect but I doubt that I would have much luck finding the shank units. Like I said I want to use the existing frame but want to use a different shank that would be common and easily replaced.
  10. B

    Dearborn Shank Conversion

    Has anybody ever converted a 3pt Dearborn cultivator to a more rugged shank? I have broken 2 of my shanks on the cultivator now and want to find a renewable and more rugged option. I use this for foodplotting and only work a couple of acres a year. I was kind of thinking of finding an old out of...
  11. B

    Engine Oil

    It is a gas 300 utility. Lots of opinions, I will probably just try the 10-30 or 15-40. I don't run it too hard.
  12. B

    Engine Oil

    Owners manual calls for sae 30 in summer. It should be fine to use 10w-30 instead correct? Sae 30 is quite expensive compared to the latter. Thanks
  13. B

    18 volt overcharge

    I just wanted to update. New altenator fixed the problem.
  14. B

    18 volt overcharge

    Well I am supposed to have the new altenator today. Probably wont get to test it till tomorrow night. Hopefully that fixes it.
  15. B

    18 volt overcharge

    Alright I will try moving the tie in point further back to see if it makes a difference. Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top