(800) 853-2651
SHOP NOW

Recent content by BRAD ENGLUND

Yesterday's Tractor Forums
  1. B

    jd rx75 riding mower

    I have an rx75 nd riding mower. The problem is it will not move. It goes into gear and the pulley that runs off of the engine is moving. The belts are good. The only thing I can see wrong is that the clutch pedal is setting head to far and will not return back to center position. Any help...
  2. B

    3010 rail forks

    What has happen is I have all the lower gears. However I do not have the high gears. I have tryed to adjust the shifting levers. It feels like it wants to go into the gear but keeps kicking back out. I hope that helps you guys out with my problem. Thanks for your help
  3. B

    3010 rail forks

    I am woundering how to fix the rail forks. They way I understand it is ther are two pieaces of tin and have broken off. Does a guy have to splite the tractor or can I take the top floor plate and get in it there? HOw much will the parts coast? any helps would be helpfull. Thanks brad
  4. B

    3010 rail forks

    I have a 3010 JD I am haveing problems with the transmisson. I have all the lower gears and reverse. However I do not have the higher gears. I have tryed to adjust the limkigs and that has not worked for me. I have read the shop book and did not reallly find anything out there. How can I fix...
  5. B

    4020 shifting rail

    i am looking at buying and overhauling a dieasl 4020 jd. the owner said that the shifting rail is out of the tractor. What do they mean by that? Is it the part inside with the clutch that makes it go in and out of gears? who difficult is it to fix and how much do you think parts are going to be...
  6. B

    3010 gas gov.

    I have a gas 3010 JD. The gov. is leaking oil once I shut off the tractor. I have tried to tighten the bolts and it still leaks. How hard is it to replace the gasket? Is there any other thing that I need to know about the replacement process of this?
  7. B

    JD 318

    I took the head off and the oil pane off. I have the parts on order. The only thing that I need now is in what order do I need to tighten the head bolts down and how tight? Also how tight and what order do I need to tighten the oil pan down to. Thanks for all your help again. brad
  8. B

    JD 318

    The engine # is B43-GA018/4174C. I took off the head the valves move freely. The valves have some carbon build up. Is that normal and should I clean this up while I have it this fare. The cylinder is not moving. I can push it all the way back if I hold it in and turn the engine over the cylinder...
  9. B

    m carburator

    Thank you to all that have replyed to my question. I will try to tighten the bolts. If that don't work i will try getting a new gasket. Thanks again.
  10. B

    m carburator

    I recently replaced the head on my M tractor. After putting everything back on it and getting it running. When driving the tractor down the road it does not seam to run just right. I can push the chock in it will run better. I have tried to adjust both of the points on the carburetor while it...
  11. B

    JD 318

    How do I know if the seats loose and how do I fix it? The valve I know that I need to take those out and clean with some emery cloth. Once I figure what is wrong with it what is the sequence to tighten the bolts down on the head? I appreciate all the help that you have given me. Thanks again Brad
  12. B

    JD 318

    Thanks for all fo your help. I will try and do all of those things you said to do. Thanks again
  13. B

    JD 318

    I have an JD 318 riding lawn mower. The engin is an Onen. One of the cylinders does not have compression. It was runnig fine before that. I talked to a small engine house. There the guy said it could be a stulked valve. Is that what it is or is it s combination of both? What do I need to do...
  14. B

    3010 carburator

    thanks i will give that a try
  15. B

    3010 carburator

    I have a 3010 gas tractor. It will run fine just sitting. their. When I start to go up a hill or put it under load it will start to lug down. The other thing that it will do is idle up on its own. I can slow it down by moving the rode by the carburetor. What should I be doing? Should I try to...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top