(800) 853-2651
SHOP NOW

Recent content by Charnerl

Yesterday's Tractor Forums
  1. C

    Ford ? Model

    I have a friend who ask for info on his ford. I can't find it. Serial No. is 128965 with diamond on each end. It's blue, but that don't mean anything. It has a roll type hood as NAAs and there is no front round emblem. It does have a half moon on the front of the hood roll about the size and...
  2. C

    starting issues

    I had the smae problem a year or so ago. No effort with carb. or timing seem to help. My sulusion, drill a hole in the "S" shape air cleaner pipe. Clean the pipe throughly to remove all shavings. Size the hole so a bolt will plug it. Your first start, remove the bolt and spay in starter...
  3. C

    Hydraulic lift control forks and control valve

    You may or may not need to replace the "T" valve. It slids out the back and the new one slids right in. The two prongs are sprad apart and slip onto the end of the "T" valve. I did notice the two prongs going down to the "T" valve seem to be spread apart. If so it will probably slip off the...
  4. C

    Flywheel disassembly

    Make sure the FW and ring gear is wire brushed clean before attempting to reinstall.
  5. C

    square can coil nut

    Solve your problem in the future by cutting the end off the circular wire connector and make it a fork type. No more nut removal necessary.
  6. C

    Shutting off Gas

    Not necessary. There is a drain in the bottom of most carburators which allows the fuel to slowly drain out while sitting up. It's call air horn drain.
  7. C

    New Project

    I bought an 8N one time that had a hole as you discribed. Owner told me the "fork" in the clutch shaft would turn because it was worn. He would stick a rod in the hole and put it back in place. It was happening so often he elected to get rid of it, to my good fortune. I pulled the tractor...
  8. C

    2n help - no gears

    Is your clutch working OK? Will the shift lever go into the slot or is it stuck in neutral?
  9. C

    work

    I work for about $20 hr for local folks I know. I charge $30 hr if he helps.
  10. C

    Mounting the gas tank

    Good and snug. Maybe 20-30 lbs.
  11. C

    head gasket

    Sounds like you are losing compression only. Should have no problem running temporarily.
  12. C

    8n or 9n?

    You noted all the differences and it is a 9N. I had a simalar argument with a gentlemen and he proved I was wrong by producing the bill of sale stating it was an 8N. I told him the bill of sale could say it was an elephant but it was still a 9N. Some people just want hear the truth.
  13. C

    2N in frame?

    If you want an experience that will make you feel good and have accomplished something, get you a local 8N or 9N owner that has overhauled an engine. He can give you a list of things needed to strip the engine down. Once stripped, he can talk you through the installation of a top end kit. Kit...
  14. C

    Sandy visits the Garaj Mahal

    If tree is dead or living doesn't make any difference. The adjusters are so busy up there that they will probably just drive by and throw money out the car window.
  15. C

    1954 Ford NAA

    Give her the $875 and kiss her, you got a deal.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top