(800) 853-2651
SHOP NOW

Recent content by Chuckwagon

Yesterday's Tractor Forums
  1. C

    M5700 hyd issue

    Yes the connections and fluid are ok. I can see the hyd hose move when I move the joy stick. A kubota dealer said to check the control cable ?? From what I can see the joy stick is controling the valve body.
  2. C

    M5700 hyd issue

    Hi I was working my Kubota M5700 today, everything was great. I just finished grading the area and went to lift the bucket, won"t lift up ??? I can lift the front wheels of the ground with the tilt, but can"t raise the bucket off the ground now. Any suggesting"s..Thank you in advance.. Chuck..
  3. C

    NH 315 baler

    Thanks JD, I'll disconnect the pins and swing the assembly's up and check the clearances before I attempt to make any adjustments. I'm between cutting and baling right now, so I have some time to inspect and look it all over before I try to make any adjustments. Just want to thank everyone, I...
  4. C

    NH 315 baler

    Thanks Gordo for your input. From the sound of it I'm getting the impression you knew it all. I thought this site was to help each other when a issue came along that you couldn't figure out, even when you do have books....... It's not the $20.00 for the book, books don't always explain...
  5. C

    NH 315 baler

    wc Mike, I'll give that a try
  6. C

    NH 315 baler

    Delta, can that be adjusted ? If so how ? as you can proberly tell I don't have a book..
  7. C

    NH 315 baler

    I have a NH 315 baler the 95% of the time it works great. The other 5% it starts bunching up 2 strings around the bird-bill on the right side. Mostly when I have to restring, but it has done it on it's own. After I clear it may do it again one more time. The bird-bill is clean and shinny. I do...
  8. C

    Position Control Device

    Sounds good, I'll be standing by..
  9. C

    Position Control Device

    Grandpa do you still have that Zang Thang I"d like to install it on my TO-20
  10. C

    Parts ?

    Paul I called them they had everything but the needle bearings, but they gave me the part number for them which is a great help. Hopefully I can get them close to home. At least it gives me some to work with. Thanks for the help and fast response...
  11. C

    Parts ?

    I didn't mention, The tractor is a 1951 TO-20
  12. C

    Parts ?

    I had a problem with my governer and it was affecting the carburetor, rpm settings. I had to remove my front end to get at the problem. I had found the needle bearings were worn which made the seal leak. Now that I have it torn down I can"t find where to buy the needle bearings. (No YT does not...
  13. C

    1951 Ferguson TO20

    Hi GrandpaJack do you still have these tires & tubes. Do you have the rims that go with them. My rims are pretty rusted up around the vavle stem hole. what are you asking for them. Thank you.
  14. C

    Oil leak

    Got ya... I guess it"s time to roll up the sleeves and get dirty......... Thanks....
  15. C

    Oil leak

    Setting that aside, (future ring job) Why is oil showing up around the plugs ? High compression wouldn"t do that, so how can low compression cause it ? Correct me if I"m wrong, but in my opinion bad rings would be blowing smoke out of the exhaust, not pushing it out from the spark plugs. Is it...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top