(800) 853-2651
SHOP NOW

Recent content by Clelle

Yesterday's Tractor Forums
  1. C

    OT- Dodge truck doors

    You most certainly can I do not know if it will let me link another site but www.Dieseltruckresource.com in the 1st generation forum section, there is a "sticky" of threads and one of them describes in detail just how to put the crank windows in an electric window truck. I realize you said a...
  2. C

    NEWBIE NAA questions

    **UPDATE** My father called me back finally after sending him your advise, and good news with the new oil in al 3 compartments the NAA is off and shifting smoothly into and out of all gears. Also the lift stopped shuddering with the correct oil in it as well.... imagine that :D Thanks...
  3. C

    NEWBIE NAA questions

    I own an 8n so I do not know too much about the Jubilees and NAA, that said, my father called me this morning and he is out with grandpa working on his old NAA in Hermleigh TX and asking me questions about it. I am all the way in AZ and am not too much help at this time. It is running but will...
  4. C

    WAY OT- For you California boys

    I don't know if any of you boys are hunters or shooters , but if you are you may want to check this out and sign this NRA petition to appeal the law that would require you to be fingerprinted upon purchasing ammo in the state of CA and no longer allows mail order ammo purchases...
  5. C

    Flipping rears around

    I most certainly do have one of those wonderful manuals, I actually think i have one out in my truck here at work. Just never thought to check it out... Thanks for the replies gentlemen my mind is now at ease!!
  6. C

    Flipping rears around

    If I wanted to make the rear of my 1948 8N Mut 6 volt front mount stance a bit wider, would it create any excess stress on the rear studs to just flip the tires around? Being that the center of the tires is not over the axle?? :?
  7. C

    Broken Generator Stud **Update**

    **1947 8n MUT 6 volt front mount** I asked a question the other day about how to get my generator apart to retrieve a broken generator ground bolt. It all came apart very easilly, while I was in there I tightened the loose Field and Arm studs as well. A short trip to the hardware store to pick...
  8. C

    8N not running under load.

    I would say to go back and look at the plug wires and make sure they are in the right order.... 1 2 4 3 CCW on the Dist.... these motors are so good they will run on 2 Cylinders and have no power under load... this would be for the front mount dist... HTH
  9. C

    Broken Generator Stud

    I suppose if all I need to do is match it up I will take a trip to my dad"s house. He has never thrown a bolt out from anything, coffee cans upon coffee can full of nuts and bolts. Thanks for the replys gentlemen, I will give her a go this weekend.
  10. C

    Broken Generator Stud

    So is there a parts kits tht I can get with the studs and replaceable small parts if need be, or can I just put another stud/bolt with small head in there?
  11. C

    Broken Generator Stud

    First off hello to all and hope the winter is treating people well. Don't post often but I do read on here quite a bit. Now to the problem..... 1948 6 volt positive ground front mount mutt of an N; I noticed that my tractor was no longer showing a charge when running, I know the ammeter works...
  12. C

    OT spiral ham

    I like to throw it in the oven for like 3 hours at like 250 degrees, then take out to glaze and put back in for another 15 minutes or so..... allways a smash hit
  13. C

    Seat time plowing snow in Castle Rock

    I might get some seat time mowing this weekend..... Here in central Arizona not to much call for clearing the snow out of the drive :P today its Sunny with a high of 85
  14. C

    2N Rims

    I have both of my 19inchers Slimed to the hilt on the front on my 8n, as long as they have some air in them and are spinning the slime does the rest. No complaints here, an I have to deal with lots of mesquite trees and BIG wooden thorns!!! :D
  15. C

    46 2N Getting some wood to carve (picture)

    Maybe I am missing something but how do you start that bad boy.... I cant see a battery in the picture?? :D
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top