(800) 853-2651
SHOP NOW

Recent content by Devon Hubbard

Yesterday's Tractor Forums
  1. D

    146 and 148 JD loaders

    I believe that the 146 has a single cylinder for the bucket. The 148 has dual bucket cylinders.
  2. D

    3 point john deere brush hog

    It could thump you on the back of the head.
  3. D

    Adding loader vavle to a 1970 2520D SyncroRange

    I have a 2520 gas with a 148 loader. There is a metal hydraulic line that runs under the platform to a pressure control valve under the cowling (just to the right of tachometer). I replaced the metal hydraulic line with a hydraulic hose and tee-d in between the hydraulic hose and the pressure...
  4. D

    Revisit stihl chainsaws

    It has never been gassed up. I bought it new & it is a shelf queen.
  5. D

    Revisit stihl chainsaws

    The 026 is a good saw. Perfect weight & power. I've got a new one put back to show my grandkids some day.
  6. D

    148 Loader Cylinders

    The V-packing is tight. I wound up orienting the v-packing the wrong direction and it goes in a bit easier that way. But stil sheared some off. It is working fine & hasn"t leaked yet. Be sure to remove the grease zerk out of the end of the cylinder before you bounce it on a board on a...
  7. D

    Homemade quick attach for loader-pictures

    Fred, Thanks for posting this. I'm going to try to build one for my loader.
  8. D

    2520 Radiator Leak

    I smell anti-freeze when it is running. It appears to be a pin hole leak. Would I be better off trying to get the radiator repaired or buy new? 1970 2520 gas.
  9. D

    OT - Armadillo in Kansas

    Nine full days of subfreezing temperature is supposed to annihilate them. I hate the nasty things.
  10. D

    John Deere Disk Identification

    I would appreciate knowing what model this disk is. I'm thinking about buying it. Thanks!!
  11. D

    Ford 101 3pt 3 Bottom plow 14 moldboards plow

    Per a Ford 101 operator's manual, the 14" plow needs 56" front wheel spacing & 60" rear wheel spacing. Those are center-to-center measurements.
  12. D

    Wheel Spacing

    Your reply makes perfect sense. I appreciate your input. A couple of the other replies had me scratching my head. Thanks!!
  13. D

    Wheel Spacing

    How is wheel spacing measured? I'm trying to set up properly for a plow. Plow manual says 30" wheel spacing. 2520 with 15.5 X 38's. Plow is an F145H 3X16. Is it from the centerline of the tractor to the center of the tire? Or is it from the centerline of the tractor to the inside edge of...
  14. D

    learning to read land descriptions

    As a real estate appraiser, I read legal descriptions on a daily basis. They are usually easiest to comprehend if read backwards. Start at the Section, Township & Range. Spin your chair around so that you are facing north. Draw a square on a piece of paper. That square represents 5,280 feet...
  15. D

    Gonna buy a 3020

    Hogleg, what part of the country are you located in? I've got a good 148 loader that I will sell right. I'm in NE Oklahoma......
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top