(800) 853-2651
SHOP NOW

Recent content by dyno denny

Yesterday's Tractor Forums
  1. G

    Case SC and MM-U

    In an auction today, a Case SC with eagle hitch and wide-front $325 and a MM U with wide front $225, I think they both went for scrap.
  2. R

    Super 77 Hydraulics

    I have a Super 77 that has the Lift assist for the cultivators. I would like to convert it over to a Hydraulic system with the I believe 2-remotes. Anywhere I can find one? I"m located in East Central Missouri.
  3. D

    odd ball 8n inline 6 engine need help

    Front mount distributer or side mount? They have different water pumps. I got one for my son's Funk 6 cyl front mount from Kantor.com I have a NOS pump for a earlier 40's 6 cyl for sale. I overhauled it last summer and it runs sweet. The extra power is awsome. I also know of someone who has a...
  4. D

    Erskine V Plow Snow Blower 7 Foot

    P.S.I forgot to answer 1 of your questions. If you take off 2' it will really crab you sideways. My dad's 5' had a 2' extension that you could put on the right side. It was behind a E-3 C0-0P. My son has a 7' behind his 8-n 6 cyl Funk and with the pto speed at 750-800 it REALLY moves the snow.
  5. D

    Erskine V Plow Snow Blower 7 Foot

    I have a 7" Erskine (Berger Mfg) that I have had since about 1972. It is behind my 49 8n and has moved more snow than you can imagine here in SD and when I lived in MN. Yes, wet snow is a bear with many blowers but if it is dry I wouldn"t be without it. You may have to raise it up some and...
  6. D

    block heater

    I have had the same tank heater on my 8-n for about 35+ years. I put a 5/8 hose adapter in the drain plug on the left rear of the block and bought an adapter that is for 5/8 hose and threaded on the other end with 2 curved washers and a nut. Drill a hole in the lower hose,install adapter...
  7. D

    12 volt conversion

    I put a Delco alt. on my 48-8n but to get it to start charging without reving it up, I bought the smallest pulley (2 1/2")I could find that would fit the original belt. I bored out the pulley to fit the shaft and I don"t have to get much above idle to charge. I also put 12 volt fields in a 6...
  8. D

    slopy orc on pto

    My 8n is sloppy also but the wear is inside the orc. It still works well with my 7" Erskine smow blower that I have had since the early 70"s.
  9. D

    8n Funk

    The rears are 13-28 Montgomery Ward with that crooked L pattern. Harder than hockey pucks. The fronts are brand new, still have the nipples on the face. The governor lopes at high speed, I'll try and adjust the linkage. It needs a pto seal. I'm looking to change the fields in the 6 volt gen...
  10. D

    8n Funk

    Here is a picture of a 47 8N my son bought last month. Lift arms were stuck in the up position (exhaust control valve stuck), Lights aren"t hooked up after the repaint job. Put a carb kit in it and it runs pretty smooth. It came with a dearborn loader but was never put on this tractor. Also...
  11. D

    DC-4 Clutch

    I think it adjusts the same as a model L. There should be an inspection cover on the left side. The throw out bearing rotats but first a spring loaded pin must be pulled out to allow it to turn. Years ago I watched my uncle adjust the old L and the DC MAY be the same. Hope this helps
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top