(800) 853-2651
SHOP NOW

Recent content by ewbeye

Yesterday's Tractor Forums
  1. E

    K2

    Scott your steering wheel locking mechanism frame section below the cab is probably cracked or broken. If so, lower the throat completely to allow room below the cab. Then unscrew the 4 steering hyd line fittings under the cab. Let them drain in a bucket, clean them, label with tape to id...
  2. E

    John Deere 444 into a 420 cornhead

    Yes, a 4 row 20" spacing header.
  3. E

    John Deere 444 into a 420 cornhead

    I have a good used JD 444 cornhead that I want to convert over to a 420" cornhead for my smaller K2 gleaner combine. My background is gleaners, not JD. Is there anything I need to address on these jd units in the process? Some of the snap rollers look to be lightly chipped in the front -...
  4. E

    sidedress fertilizer injection

    I have an old cultivator toolbar that I am going to convert over to a liquid fertilizer sidedress toolbar applicator. Which coulter injection units are best? FAST in Gilman,IL recommends this Clymer type? It is a knife, but it also comes with an injection knozzle. Smooth or wavy coulter? I...
  5. E

    Gleaner E auger finger guides

    Scott, try fabricating a set from a dense poly-plastic material. A K2 gleaner that I acquired from a farm auction had these on it. The farmer who own it told me he fashioned them from 1/2" blue poly. Most of them are still holding good even today.
  6. E

    drainage tile plow?

    Would an older AC 7580 be a good tractor for operating a newer laser modified drainage tile plow?
  7. E

    Continental F162?

    My AC 706 forklift has a Continental F162 engine in it. I went to start it today and the engine has no spark. I found that the distributor shaft was not turning when trying to start it. I tried turning it by hand and it would not turn. It seemed to be in gear with cam or crank - I not sure which...
  8. E

    Continental F162 distributor ?

    My AC 706 forklift has a Continental F162 engine in it. I went to start it today and the engine has no spark. I found that the distributor shaft was not turning when trying to start it. I tried turning it by hand and it would not turn. It seemed to be in gear with cam or crank - I not sure which...
  9. E

    AC 706B forklift

    Does anyone know where I can get decals for my AC 706B forklift?
  10. E

    IH #60 stalk shredder

    Does anyone on here know anything about the older IH #60 stalk shredders? Good or bad points? Currently, I have my eye on a 15' pull type. I see where I can still get flail parts for it. Thanks - Eric
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top