(800) 853-2651
SHOP NOW

Recent content by F-250 man

Yesterday's Tractor Forums
  1. B

    8n hydraulic pulse

    a new to me project, hydraulics lifts 5' brush hog with no problem but while it is up it pulses and there is slight up and down movement of the load about 2 movement, what should I check first? Thanks
  2. Destroked 450

    5000 at auction

    Watched this 5000 sell at auction yesterday, had a hard time not bidding on it myself, December 74 model with 2 spd pto, 16.9-34 rears, one wheel needed a patch, the other had been patched, grill was missing and grill shell had a good sized dent, dual remote valve, Dunham 22 quick attach loader...
  3. C

    fuel line

    would there be a problem using a brake line for a Jubilee fuel line?
  4. M

    scootergmc

    You replied to my post about the 610 vs 903 carbs. I took your advice and looked into the distributor before changing the carb. I found a lot of old grease and the flyweights are rusty but do move. Don't know if they're working though. It's a Mallory, not the original Holley. How can I get the...
  5. K

    Deere alternator questions

    I was trouble shooting the non-advancing hour meter on my 5500N yesterday. Following the Technical manual instructions, I got to the step to verify alternator output- had battery voltage at the big lead and also at the IG terminal with KOEO. When testing at low idle, I had no voltage at the L...
  6. nashranch

    LUC running

    https://www.youtube.com/watch?v=kadN6roU8J0
  7. 3

    Piston rings

    I bought a set of rings for my 13 hp Honda motor for my pressure washer. One ring is chrome and the other is black. I am thinking the chrome face ring goes on top. Any thoughts? Stan
  8. X

    8n maybe a 1952 brake question?

    First time posting but long time follower. I am redoing my brakes and ran into 2 issues. 1st issue is the top brake on the right side does not lift up when I step on the brake? I have since cleaned it up but have not tried it to see if it works yet. 2nd issue involves something that I cant...
  9. W

    I'll give ya something to WINE about!

    Well, it'll actually cost you about 700.oo- its a "re-purposed" 9N hood, listed as an "8N" and for sale on FB. Like most "restored" 9N/2Ns, he also used 8N colours.... 9n hood / wine tasting table
  10. R

    Help Bleeding Brakes

    1941 Chevy Flatbed truck. Freshing this up, Motor rebuild some paint and body work. Installed new brake shoes, wheel cylinders, all lines. Installed a new duel master cylinder with vacuum boost and a proportioning valve. Have bled and bled the system numerous times and can not get a pedal. Tried...
  11. rustred

    88 oil filter.

    i was surprised today to find out oil filters for the oliver 88 are hard to get. went to napa the guy said 30.00 and i will have to locate one and get it in. went to bumper to bumper same B.S. so i stoppped at the dealer and he happened to have one on the shelf. 21.00 was happy to get it and...
  12. G

    Ignition switch for Oliver 550 (1966)

    Hi, I'm looking for an ignition switch for my dad's oliver 550 tractor that is made in a ~1966. My question is-is an ignition switch and key switch the same thing? Any help is appreciated figuring out what he needs.
  13. A

    Case 2090 will not move in power shift #1 or reverse

    I asked this question several weeks ago and someone mentioned that a lot of the J.I. Case guys were putting in the crop and not visiting Yesterdays Tractors on a regular basis. I had ordered a new cab kit for my Case 2090. Gutted the old cab interior and drove the tractor to town to the car...
  14. B

    Ford 9nan Holley vapouriser

    Can someone send me a diagram or explain how this works. Carb needle setting would be handy too.
  15. T

    D17 Rocker Arm Oil Tube

    We are restoring a D17 Allis Chalmers Series 3. Thanks to this site we now have it running after it sat locked up in a barn for 7 years. While adjusting the valves last week we noticed the small oil tube that comes up and curves into the top of the rocker arm (I don't know the official name) is...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top