(800) 853-2651
SHOP NOW

Recent content by gmonnens

Yesterday's Tractor Forums
  1. G

    Super C Farmall transmission, differential & drive oil

    I have a Super C Farmall. The transmission, differential and drive gears use a common case and oil reservoir. Does that take 19 quarts of oil? Can I use Gear Lube 8090? How do I check the level of the oil? Can a dip stick be made and then measure from the "fill hole?" Feedback...
  2. G

    706 tachometer cable

    I have a Model F706D S/N #: 3082 S-Y. My tachometer cable is broken. Trying to find the correct cable to buy. I called Yesterday's Tractor and was informed to get more information since they could not help me with the information I provided. How do I proceed in determining what type of...
  3. G

    Tachometer on a F706D

    Thank you Gary
  4. G

    Tachometer on a F706D

    Thank you Gary
  5. G

    Tachometer on a F706D

    THANK YOU Gary
  6. G

    Tachometer on a F706D

    I have a Farmall F706D. S/N: 3082 S-Y. My tach has quit working. Looking for advice on where to begin repair. Thank you.
  7. G

    Farmall Super C

    I have a Farmall Super C. I am looking for a place to buy bushings and 1 and 2 groove pulleys for the upper PTO. (Usually used for driving a mower). Website or actual retailer (near the Eau Claire, WI area) is what I am looking for. What is the technical description of the PTO? Thank you.
  8. G

    Super C brakes

    I like your screen name! Thank you for the information on the brake covers. When I get the new parts I will check the tolerance. I have a Bridgeport in which I could use an end mill or a fly cutter. I also have a 4 jaw chuck for my lathe that I could use. Do you have a recommendation...
  9. G

    Super C brakes

    I have just acquired a Super C. The brakes are in need of repair. I plan on ordering 4 discs and 4 new springs. On the lined disc that is currently in place, the rivets cut grooves into the actuating disc. The grooves that were cut into the actuating disc are 50,000ths in depth. Can I...
  10. G

    H Farmall

    My H is without fenders. Is there a place to buy fenders or does someone manufacture aftermarket fenders? Thank you!
  11. G

    H Farmall

    I am putting a new countershaft in my H. I have removed the old dog style countershaft and installing the newer spline countershaft. When I was installing the new shaft, it would not go in. The constant mesh gear, the large one, hits the oil runs on the side of the rear frame and this is...
  12. G

    H Farmall

    I have an H Farmall with an intake exhaust manifold which has a lever in it for dual fuel. The handle and the bar has been removed because it was loose. Was there a flap at one time secured to this handle and bolt that came out? If so, how should I proceed? Another question....Is the intake...
  13. G

    H Farmall

    This is my first attempt to rebuild a tractor. I have a H Farmall with a bad pto. I have an old style pto with the dogs and will change to the better style. My question is the countershaft and pto in a M the same as the H? I have a M parts tractor. Or are there other tractors that have...
  14. G

    H Farmall

    I have an H and the power takeoff is not working. I have looked in through the pto hole and both dogs on the transmission counter shaft are broken off. I believe this is so, but cannot find them in the transmission housing. It has been suggested that I change to the newer spline pto. I hear...
  15. G

    H Farmall

    A week or so ago I had asked a repair question and was told to purchase an owner"s manual and a service manual. A found the manuals on external_link. but have not purchased them as of yet. I am now looking for a recommendation on the best manuals to buy for a 1940 H tractor. Also, the seller...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top