(800) 853-2651
SHOP NOW

Recent content by Gord William

Yesterday's Tractor Forums
  1. G

    4 in 1 Bucket made by Kitchin Engineering Ltd ?

    Hi all. I have a 88 wide 1 cubic meter 4 in 1 bucket made by Kitchin Engineering Ltd in Chesterfield England that I picked up at an auction. I may try and mount it on my MF 202 Workbull ( although its a little big and a bit heavy). I think my rear tire spread with the industrial tires is 78 so...
  2. G

    Hydraulic cylinder disassembly

    Hi Stan, its for my MF 202 backhoe. Its the crowd cylinder on my hoe of my Massey Ferguson backhoe. The actual hoe model is 220. I do have a purchased manual and can see the drawing and instructions for disassembly but the bearing wont tap in far enough to allow the retaining ring to be...
  3. G

    Hydraulic cylinder disassembly

    Yep, your right, its the packing inside thats leaking out through the wiper seal. Ive reassembled the cylinder for the moment as I have a couple things to do with the hoe before the black flies come this spring. I had thought I could have it out, repaired and back in, in maybe 1 or 2 days...
  4. G

    Hydraulic cylinder disassembly

    Hi Stan, its for my MF 202 backhoe. Its the crowd cylinder on my hoe of my Massey Ferguson backhoe. The actual hoe model is 220. I do have a purchased manual and can see the drawing and instructions for disassembly but the bearing wont tap in far enough to allow the retaining ring to be...
  5. G

    Hydraulic cylinder disassembly

    Hi all. Im taking a hydraulic cylinder apart on my MF Work-bull but am having problems. Ive removed the lock nut and tapped the bearing further into the cylinder to allow the removal of the retaining ring. Problem is, the bearing wont go in far enough ( using a brass punch and hammer) to...
  6. G

    Workbull 202 Pulley Adaptor for Hydraulic Pump

    Im getting ready to re-install the hydraulic pump on the front of my MF 202. I noticed the drive shaft ( when threaded into the adaptor plate) isnt centred in the pivot pin. ( The pivot pin, bushings, adapter plate and drive shaft are new). I can put the hydraulic pump on the shaft and get the...
  7. G

    MF Work Bull Z134 Timing ?

    Ahhh so Im not the only one with a turned distributor. I will put the old longer #4 wire back on for now as the new one is really a stretch. I too will eventually remove and reinstall the distributor but for right now it will have to stay as is. I need to concentrate on getting the tractor out...
  8. G

    MF Work Bull Z134 Timing ?

    I think I should have known it was gears but I didnt. Lol. Thanks for setting that straight. I will eventually remove and reinstall the distributor but that will have to wait for right now. I appreciate your reply. Gord
  9. G

    MF Work Bull Z134 Timing ?

    Hi all. I have a 1964 202 work bull that I bought a while back. Ive just completed installing the front axle and wheels after replacing pivot pin and bushings and blah blah , long story. Still havent installed the water pump or front nose but want to know before its completely back together...
  10. G

    Howard Rotovator

    Thats a lot of H.P, my tractor doesnt come close lol. I was wanting to use my 1954 28hp Ferguson TEA tractor with the Rotovator but the lever to disengage the gear box on the Rotovator is missing ( Ill have to make one). Because its not a live pto tractor its difficult to use the Rotovator...
  11. G

    Howard Rotovator

    Hi, how old is your tiller and what tractor are you running it on? 90 inches is a fairly large tiller.
  12. G

    Howard Rotovator

    How old is your rotary hoe? 90 inches is pretty big, what tractor are you running it with? Im located a few hours drive north of Toronto Canada where the farmland has a lot of bedrock and large stone. On a Saturday morning its common to here the clang of mower blades on rock in the distance as...
  13. G

    Howard Rotovator

    Hi, I did find a manual on line and downloaded it. It does show the Rotovator being attached as I am attempting to do. This particular Rotovator is a 4 point hitch from everything Ive read and by looking at pictures Ive seen. The 3 point hitch top link on the tractor isnt used for this...
  14. G

    Howard Rotovator

    More Pictures that didn't load before.
  15. G

    Howard Rotovator

    Hi Folks, I have a Howard Rotovator Tractor Attachment I am wanting to run with my 1954 TEA tractor but I have some questions and I would appreciate any feedback or experience anyone reading this has. The Rotovator is a centred, not offset and has a 1 3/16 square drive pto shaft but no matching...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top