(800) 853-2651
SHOP NOW

Recent content by gwoc

Yesterday's Tractor Forums
  1. G

    pto shaft length

    Thanks for everyone's comments. I was mainly concerned about the extra 7/8". I've owned 11 Ford tractors, so I'm not new to tractor lore. Again, thanks!
  2. G

    pto shaft length

    Already have one. Thanks.
  3. G

    pto shaft length

    Thanks! And, I am upgrading.
  4. G

    pto shaft length

    Replacing pto shaft assy in my '52 8N. Old shaft is 30". All replacements seem to be 30-7/8". Will that fit?
  5. G

    '52 8N lift control arm broken

    Removed lift control lid to rebuild. Pump control arm tipis broken off. Can it be repaired?
  6. G

    napa parts cross refrence

    NAPA Ford Tractor Part Numbers: Front Mount distributor... Points: NAPA #CS35 Standard Ignition Blue Streak #FD-6769X (Premium) Condensor: NAPA #FA200 Standard Ignition #FD-71 Rotor: NAPA #FA300 Standard Ignition #FD-104 Distributor Cap: NAPA #FA350 Standard Ignition #FD-126 Coil IC670...
  7. G

    Boom for a 3PT post hole digger

    I bought a post hole auger, gearhead, and pto shaft at an estate sale for $50. The boom had broken off near the u-shaped support that connects to the 3 pt. lift arms. The piece of the boom that connects and supports the gearhead was nowhere to be found. The mounting surface on the gearhead is 6...
  8. G

    Boom for a 3PT post hole digger

    I bought a post hole auger, gearhead, and pto shaft at an estate sale for $50. The boom had broken off near the u-shaped support that connects to the 3 pt. lift arms. The piece of the boom that connects and supports the gearhead was nowhere to be found. The mounting surface on the gearhead is 6...
  9. G

    Potential 641 purchase

    Went to see it and decided to buy it. It had a few typical issues but started easily. The tires were like new. It's like buying tires with a tractor attached.
  10. G

    Potential 641 purchase

    I'm going to look at a '59 641 tractor that the owner wants to sell for $1000. He says that the lift doesn't work. He claims that everything works and it has like new tires. What are some of the possible fixes might I expect to repair the lift. Is there a lift problem that I should consider a...
  11. G

    Starter Button

    Check wire connection to your solenoid if you have one. Could be loose.
  12. G

    Potential 800 Series purchase

    Thanks. With the larger engine I would expect more fuel consumption, but I agree, a carb can make a difference.
  13. G

    Potential 800 Series purchase

    I'm considering this 800 series tractor. I've owned a 9N, five 8N, and a Jubilee. Are there any inherent weaknesses with the 800 series I should be concerned about? https://athensga.craigslist.org/grd/d/1956-ford-800-tractor/6442082441.html
    • gwoc
    • Thread
    • Replies: 12
    • Forum: Ford
  14. G

    Jubilee valve adjustment

    It's obvious the PO used a lot of "trial and error" methods. I don't think he was able to get it running to burn the valves.
  15. G

    Jubilee valve adjustment

    Over the last 10 years I've owned a 9N and (4) 8Ns. I recently bought a well-used Jubilee. A compression check showed fairly good compression in cylinders 1, 2, and 3. Cylinder 4 showed about 30 psi. I checked the gap between the valves and rocker arms with the piston at TDC and found no gap...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top