(800) 853-2651
SHOP NOW

Recent content by J88puller

Yesterday's Tractor Forums
  1. J

    Hubs info for Ac-B,C,Ca

    Thank you for taking the time to look it up but it appears that I did not mention it was the bearing hubs for the front wheels that I am needing the size for.
  2. J

    Hubs info for Ac-B,C,Ca

    Can someone please tell me the bearing size as for as the axle shaft I guess you might call it for a C,Ca and a model B I guess they all use the same hub but i need to know the bearing size. Thanks
  3. J

    Oliver 1850 Rearend

    I just bought a 1850 gas and the guy I bought it from was driving it down the road and heard a noise and slowed it down and the rearend locked up in it. He took the shifter cover off and looked at the tranny and said that everything looked good inside of it and the cover is still off. The...
  4. J

    WHAT DOES YOUR TRACTOR HAULER LOOK LIKE? PIC

    Hey Midnightrider - you didnt use to pull a oliver 88 did you that said that said midnightrider on the side curtains did you?
  5. J

    WD-9 and 1/2 ton truck

    There is a lot of factors to take into consideration. How far are you going to be pulling it and is the roads flat or hilly and how old is your truck. If you have a newer truck there are built better than the old ones were they have tranny coolers, more power and most of the half tons upgraded...
  6. J

    WHAT DOES YOUR TRACTOR HAULER LOOK LIKE? PIC

    07 Silverado halfton and my new Oliver 1850
  7. J

    Oliver pulling engine build

    Has anyone ever tried stroking a 265block using the stock rods and small block chevy pistons 4 inchers. I know theres a difference in the piston pin locations and was wondering how much I could stroke it with those pistons. Looking for a set up to run 5mph in 5500 pound class. My 283 dies in 2nd...
  8. J

    Tow vehicle

    I have a 07 silverado half ton and a 25 foot Gooseneck trailer. Half ton pulls it just fine. I've put 6000 88 oliver on it with a golfcart and no problems, will put 2 tractors on it this year weight for both will be about 11,000 truck has the 5.3 in it. 3/4 ton would be better but I only use it...
  9. J

    Trailers

    I bought a new 20+5 gator trailer almost a year ago. I like the trailer but i did not go with the elite series. One reason was the price the 2nd was the big bulk head on the front of it. I figured that you would not be able to see any of your load on the trailer. I ordered mine with 3 ramps and...
  10. J

    Oliver 88 RPM's

    Was wondering how many rpm a stock crank can handle in a 88 gas engine (apprx) I know some guys with the oil fed rod engines spin them pretty high but is 2000 or up to 2200 rpm still in the safe range? I know they are rated at 1650 or 1750 but that is a rpm that you can use all day for farming...
  11. J

    Pulling

    Pulling is fun. It would just be nice if every place had the same rules!! Would make things alot easier!
  12. J

    lookin 4 a oliver pulling engine

    shoot me an email about the 307 with the specs gas or diesel and price: [email protected]
  13. J

    Super 77 Diesel build up

    If you strip it and put pressed rims all the way around you can get it in the 4000 and maybe the 3500 class, If it was my tractor I would put a gas engine in it, diesel are expensive when it comes time to work on the pump, and as far as engines it all depends on how much you want to spend you...
  14. J

    lookin 4 a oliver pulling engine

    Over by Lima, Ohio
  15. J

    What's Wrong with this picture?? Ha Ha

    Would have been funny once you got there and they said by the way were pulling light to heavy
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top