Recent content by JMJ

  1. J

    Break-in engine oil

    The break in oil is used to help the ring seating. If you use John Deere break in oil it will be 10w30 break in oil. When we get our new sprayers every spring, we run break in oil in them at 100 hour intervals until they can go 100 hours without using any appreciable amount of oil which...
  2. J

    JD 7800, 7810, 7820

    whoops sorry about that. 7800 did have 7.6 l and 10 and 20 series had the 8.1. I was going from my experience with 7610's7510-20's and 78 and 7930 tractors which do all have 6.8 l engines.
  3. J

    JD 7800, 7810, 7820

    7800 is probably a power shift, 7810 will have power quad with left had reverser, 7820 will be power quad or auto quad (one lever with four electric power shift speeds) with left reverser. I think they all use the 6.8 l engine 10 series will be tier one emission standard 20 series will be tier...
  4. J

    4230 quadrange won't low-high shift

    Actually direct drive is high range (2-4). Im almost positive but wouldnt swear to it that low is actually the hydraulic shift.
  5. J

    OT: Dodge diesel steering problem

    My 01 does the same thing and my dads 97 did too. I havent gotten around too switching too synthetic in mine but we did on dads and it seems to have taken care of the problem.
  6. J

    Crank endplay on 70D

    I havent dug any deeper than the out side cover yet. I was thinking about that though. right now im 60 miles away from the tractor until tomorrow some time. If anything was worn in there wouldnt i have more endplay than i would care to have?
  7. J

    Crank endplay on 70D

    I am having some issues trying to set the endplay of the crank shaft on my 70D. I have added seven steel shims to the two older thicker shims that were already behind the thrust plate, and i still have a preload. It doesnt seem right to me that i should have to stack so many shims, but ive been...
  8. J

    Dodge Clutch Cylinders.

    If it were mine id replace the whole system. Then it just an R&R job and wont have to worry about trapped air.
  9. J

    70 D Loose flywheel

    Ive been trying to chase down my nasty clutch noise on my 55 70D for the last week or so and i think i found it. My flywheel has come loose. I dont think its been loose too long though because its probably only ran a total of maybe 5 hours so far this year and last winter it was still tight on...
  10. J

    70 D NOISY clutch

    Well i actually just had the whole assy off and apart on friday, and every thing but the operating sleeve, drive gear and the pulley its self (bearing and bushing included) is new in it right now. I looked at the bushing in it and it doesnt appear to be worn at a taper like i figured it would...
  11. J

    70 D NOISY clutch

    Well i went out and pulled the clutch brake off of the tractor, unhooked the clutch lever from the fork arm, and grabbed ahold of the pulley and gave 'er a good wiggle and i guess i do have an apprecialble amount of radial play. So ill be off to find a bearing and race and a bushing Monday. Just...
  12. J

    70 D NOISY clutch

    I"ve got a "55 70D that ive been having clutch problems with. Since i bought the tractor the clutch has been loud really rattling and clunking, and would bind up and not release with out jamming on the brakes a few times. I knew the driver and disks were pretty badly worn so i bit the bullet...
  13. J

    OT Dodge Ram 5.9 CTD

    Mine is a 24 valve but with the holes in my air box ( I actually added 7) on the dirty side, straight piped exhaust, up to 30 LBS of boost 65 HP chip and 80 HP injectors, I can gross 15K and never hit 1200 with mine. Before i put the injectors in and before i caged my wastgate and could only...
  14. J

    OT Dodge Ram 5.9 CTD

    Can safely run up to 1250 for long periods of time. Thats assuming you put the pyro on [b:0b18f0a936][u:0b18f0a936]PRE TURBO[/u:0b18f0a936][/b:0b18f0a936]. You can hit 1350 for real short bursts (5-10 sec) with out causing problems. If you notice that your EGT's are too high you can safely run...
  15. J

    Pics of syncro-range problem.

    (reply to post at 09:27:18 04/05/09) It looks to me like the left half of the shift quadrant has moved back to the park position. Is that correct. If thats the case the latch that is supposed to lock the two halves together isnt doing its job. These tractors do have a power assisted park...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top