(800) 853-2651
SHOP NOW

Recent content by John Eatwell

Yesterday's Tractor Forums
  1. J

    Kewanee disc help

    My mistake the piece you need is by the hitch, didn't see it before. Bolts to disk frame down to hitch.Sorry about that. John
  2. J

    Kewanee disc help

    That jack looking piece behind the lift cylinder is suppose to be in front of the cylinder and fasten to hitch. That is how you level the disk. The piece to hold disk in transport position is missing and someone put that there in its place or just put it there so it wouldn't get misplaced.
  3. J

    Cotton Picker Questions

    The cotton pickers are built in Ankeny, Iowa. See them leaving the plant all the time going every direction as Ankeny is on the crossroads of interstate 35 and 80.
  4. J

    Well Duh

    Helped a neighbor put a new-used engine in a pickup. When it was time to start it we found the starter was bad. The starter off the old engine was different so we decided to pull it with a tractor. I have a circle drive around the grain bins. We went around there over 10 times stopping to check...
  5. J

    Sons heritage fair project today

    You have a right to be proud of both young men as all of the people on this forum are. I would like to thank Adam Keys for his service and giving so much. Your stepson is very proud of his cousin as he should be. He will do very well in life. That is a feel good story.
  6. J

    D6 44A7289 transmission help

    Forgot to add the floor boards and brake peddles and the rest of the control levers have to be removed. If no oil you might have a lot more problems than the top bearings.
  7. J

    D6 44A7289 transmission help

    Only one way to fix transmission and that to remove it. The fuel tank and seat has to be removed, the u-joint at the front removed. The belly pan also has to be remove to get to the bottom bolts. Going back together the shaft that drives the cable unit will take some work to get lined up. I had...
  8. J

    New pto safe design connectors

    I agree with you 100 %. I had too replace one and asked if they could put on one with the old style push button and said they could, was so much easier to use.
  9. J

    Transport Trailer Inc 1954 Cedar Rapids IA

    Do you need hub and drum or just drum. The drum bolts on to hub so if you just need drum might find something that would work. My trailer has 8.25 by 15 inch tires if yours takes a bigger tire hub might not be the same. John
  10. J

    Transport Trailer Inc 1954 Cedar Rapids IA

    I went out to shed to look for part no. There was so much dust and dirt I couldn't find a number. My hub looks just like yours through. The model no. of my trailer is GPX-24, serial No.is 5934 and manufacturing date is 10-54. Sorry I couldn't be of more help, John
  11. J

    Transport Trailer Inc 1954 Cedar Rapids IA

    I will have to see what the number is on my hubs, wouldn't have a clue on the bearings as it was a while ago and at the time I changed all the hubs over to oil type seals.
  12. J

    Transport Trailer Inc 1954 Cedar Rapids IA

    I have a transport trailer just like yours, same year. I think I got a new hub from Midwest wheel in Des Moines, Iowa. Get the number off the hub and call them. It has been several years since I bought it but worth a try.
  13. J

    BMB Brute 120 Parts

    Alamo group bought out BMB, Did have parts but were pricey.
  14. J

    john deere 4020 powershift

    My 4020 power shift did the same thing. The cable was bad and also the arm on the side of transmission case was worn and roll pin was sloppy. Replaced cable, arm and roll pin and was like new. John
  15. J

    How will you secure this tractor?

    A clevis on the draw bar with chain pulling back. I chain on the front loader bracket pulling forward and a chain over loader to hold bucket down.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top