(800) 853-2651
SHOP NOW

Recent content by John UK

Yesterday's Tractor Forums
  1. J

    Transmission Fluid Leaking

    If you have filled it with 5W/30 then it could very well leak as it is very thin and isn't recommended. What was recommended however was 15W/30 and that doesn't normally leak as it is tried and tested. However if you fill your transmission with this oil and it does leak then it is the seals that...
  2. J

    TEA-20-85 vs TO-35

    Not just the TO35 but ANY 35 series All that you have mentioned plus the hydraulic system which is stronger and much more versatile that the earlier type. Steering doesn't kick and is lighter.Plus of course....MORE ENGINE POWER John
  3. J

    which model?

    Check the metal the transmission case is made from, if it is cast iron, it is a TO made in Detroit, if it is Aluminium-like it is a TE made in the UK.If you gave us the serial number it would help us to tell you what it is.If it is a TE and 1953 it will be a 12 volt.Look around the Coil and the...
  4. J

    TO 20 3rd Gear

    Remove the top cover and check the gears for wear, but it could also be wear on the selectors and the gears are not being pushed fully into mesh. It is also possible that there is wear in the bearings on the shafts which are floating back and forth, there should be no end float. It can also be...
  5. J

    TO-30

    Remove the Steering wheel and adjust the nuts underneath to prevent this, use the lock nut too. The bearings maybe shot, but it is adjustment that is causing the wheel to lift like that....John
  6. J

    solenoid TE20

    Some of these safety switches can be taken apart and you can clean the contacts, as they do burn over a period of time. If you slacken off the 4 screws that hold the switch to the top of the Clutch housing you can get a bit more contact in the switch. If you remove the Switch you can elongate...
  7. J

    TE20 STIFFENING RODS

    The factories in the UK and the USA each had their own ideas, while the UK controlled it all to some extent, Detroit made some changes and this was one of them. Maybe it was because the US market did not use loaders on the tractors like we did in the UK and Coventry always seemed to "over...
  8. J

    F40 on craigslist

    Whats the betting that someone has put a high pressure safety Valve in a low pressure tractor????? This is exactly what happens, the top cover is not strong enough (plus other parts)....John
  9. J

    TO-35 PTO Oil Seal Replacement

    Yes more gentle pressure rather than shock. The only thing usually holding the PTO bearing housing is an "O" ring around the outside and normally that does not take too much pulling to get the whole thing out. I mentioned the Bearing in the Pump shaft because I have had them collapse and wear...
  10. J

    TO-35 PTO Oil Seal Replacement

    Using a slide hammer could damage your hydraulic Pump if it is the bearing collapsed on the front end of the PTO shaft.There is only one parts list and Jeff sent you that, so just what you have is anyones guess....John
  11. J

    TO-35 PTO Oil Seal Replacement

    What usually is holding the PTO shaft in is the "O" ring seal around the outside of the Bearing Housing. If you place a bar through the hole in the PTO shaft then you can pull it out that way. It is also possible that if it is still tight and wont move that the end of the PTO shaft is worn...
  12. J

    Ferguson Plow Parts

    Have they really, Thank you for that. A sign of the times I suppose, what a shame....John
  13. J

    rubber grease boot replacement

    Do not attempt to take the joints apart. To replace the rubber boots, remove the nut that holds the joint onto the steering arm and strike the arm with a medium size hammer to shock the joint out of the taper in the arm. Don't worry about breaking anything, because it wont, just hit it and then...
  14. J

    wide open

    If you email me direct at th address below I will send you the information about repairing and re-setting the governor. It may only be settings or it could have something broken or [email protected]
  15. J

    overriding clutch

    Your loader bucket not lifting, it depends on the system used as to why it isn't lifting. If you only have the tractor lift lever, make sure that the PTO is in drive and then the Lever should lift the loader. If there are other levers on the tractor for the loader, these divert the oil and they...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top