Recent content by Johnny50

  1. J

    restoring #5 sickle mower

    the crank wheel ( the pitman arm hooks to it) on this mower seems to be just pressed on with a keyway. Do i have to use a puller or should this just come off with a a few hard taps with a hammer? thanks for any advice
  2. J

    Parts for #5 mower

    I am located way up in the Northeast and am looking for the drawbar on the #5 mower that hooks onto the two round pegs on the drawbar of a JD 50 I would like to talk to anyone who has this part.(AZ3608H) in the parts book. thanks, Roger
  3. J

    JD #5 mower

    Do these mowers have serial numbers on them? Where is it located? How do you tell the year of manufacture? I need the year of manufacture to order decals
  4. J

    50's manure spreader

    What model number manure spreader did John Deere sell from 1950 to 1955? A picture would be nice also I"m trying to put together most of the implements that would have been used with my 50
  5. J

    hauling #44 plow

    Can I haul my #44 plow behind the tractor with the tail wheel up in 6th gear for about 5 miles? It is well greased. Will the hubs heat up?
  6. J

    sickle bar mower

    I live way up in the Northeast and am looking to buy a #5 sickle bar mower. I ran across a sickle bar mower (JD) yesterday and it had two caster wheels in the back. Does anyone know what number mower this is and how old it would be? Thanks for any info. Roger
  7. J

    #44 plow rope clip

    I saw in Green Magazine where there is a clip made to put on the back of the tractor seat to attach the rope and it allows the rope to break away if the plow does. I forgot who makes these. Where can this clip be purchased?
  8. J

    #44 plow

    I have a #44 JD plow with worn out shares and landsides. (Scotch bottoms). Would it be possible to change these bottoms to another type where I could get replacement shares and bottoms? Any help would be appreciated.
  9. J

    smoke from vent pipe

    Was plowing with a 50 yesterday. working it pretty good and noticed smoke or steam coming from the vent pipe. just saw this from the seat so don"t know how much. temp and oil pressure good. Is this normal for a small amount to come out of that pipe? What should I check?
  10. J

    #44 plow

    I have a #44 JD plow with 10" scotch bottoms. I need 2 shares and 2 landsides for this plow. Any help would be appreciated, ie phone numbers or email addresses. I live in the Northeast
  11. J

    #44 plow

    restoring a #44 plow. Need points(Shears) Number on old ones were DEERE BC 459 Also need land sides. Numbers on old ones were 82 8 Anyone know where I can start looking I live in Nova Scotia but plan to go down the Eastern seaboard in the Spring.
  12. J

    pulling JD 50

    I used to pull the JD 50 in the 5000# and 6000# classes but find I"m front heavy in the 5000# class with the tractor bare. Would it be better to weigh up to the 7000#? If so how much weight out front? I put 100# about a foot from the tin in the 6000#. would 200# be enough in the 7000# class...
  13. J

    balancing a JD 50

    I'm a rookie puller. Did some weighing this afternoon. right now in the 5000# class I have 25% weight on front with 10# air in tires In 6000# class weighed up with 23% on front and will run 11# air. Can I improve this as a starting point? Lots of room to move weights in the 6000# , Not much...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top