(800) 853-2651
SHOP NOW

Recent content by KTS_B

Yesterday's Tractor Forums
  1. K

    Leaky Gas Tank

    Our WD45 tank has a leak by the corner of the mounting bracket. Wish I would have known before I put it back on after painting and filled it with gas. If you can't weld or braze it, why not JB weld?
  2. K

    Under-hood muffler on C

    What about exhaust heat wrap?
  3. K

    project b1

    simple tractors has a lot of info on them. I have a 63" B1 that we use to plow the gardens. Powerful little tractor. When we rebuilt it a few years ago a few of the parts were very hard to locate. Untitled URL Link
  4. K

    allis b

    Does your rim have the four bumps on it or is it another type? Ours looked to be in good shape, but all the bumps were worn and cracked. Had to weld up the inside and outside. If it is loose it will probably wear much faster or cause some damage. We also replaced a few of the non-eccentric...
  5. K

    Synthetic oil in tractor

    Not sure how it would do in a tractor motor but synthetic does seep past the seals in some cars. Experienced this with a turbocharged car at less than 30k miles. Went back to dino oil and it never happened again.
  6. K

    WD45 Starter Problem???

    You should still be able to get it rebuilt for a reasonable price. The starter on our B got a new switch, brushes and was turned down for less than $100. Even if it costs you more to rebuild one it will turn better than any one from the salvage yard.
  7. K

    WD45 spinout bolts stuck

    Hubs pushed out with a few swings of the sledge and an oak block. The locks took quite a bit to free up. I sand blasted them first, heated each one til nearly the whole thing was glowing. Took half a candle for the four of them and going from forward to reverse with the impact gun. Seems they...
  8. K

    WD aux hydro pump

    I need to do another pump setup to free up the pto on mine. Why couldn't a pump be ran off the pto shaft under the tractor with a belt or chain drive? That would give you the ability to turn the pump on and off. Mine has the backhoe mount so I have plenty of room around there to mount a pump on...
  9. K

    WD45 spinout bolts stuck

    So this section should just pound out from the other side since I removed the 8 bolts?
  10. K

    WD45 spinout bolts stuck

    The four locking bolts on the rim are stuck. Tried heating up the bolt with the torch and melting wax into it, twice. Then heated the block piece and not the bolt. PB blaster over several days. Still have the tubes in them so they can't get too hot. 1200 ft # impact gun didn't budge any of...
  11. K

    WD45 Loader questions

    The cylinders don't have any kind of bypass in them? I wonder if a low profile hydro pump would fit on the pto shaft and still allow a drive shaft to be put on?
  12. K

    WD45 Loader questions

    We have a 55' WD45 with I believe a Henry loader and still has a mount for a backhoe. It is running off a pto powered hydro pump right now. It has a block off plate over the original pump but I do have a good pump off another tractor. Will the original pump power the loader? Too slow? I will be...
  13. K

    WD45 rebuild questions

    Crank has been turned. The journals measured 2.363. Less than two thousandths clearance with the plastigauge. Knocked all the sleeves out using a square plate with a bolt through it that has a chain link welded to it using the electric hoist and a big hammer. No cracks that I can see, but there...
  14. K

    What plugs, Allis B?

    I'm almost certain I'm running Autolite 295. Looks like 306 is hotter and 308 being the hottest, both resistor plugs. http://www.emeraldfarm.net/farm/misc/sparkplugs.htm
  15. K

    WD45 rebuild questions

    The low compression was probably caused by the leaking valves in the middle cylinders. Both valves in the one and just the intake in the other. Thats probably why it popped and we couldn't get it to run right before we tore it apart. The intake valves have almost no wear at all from the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top