(800) 853-2651
SHOP NOW

Recent content by MasserD

Yesterday's Tractor Forums
  1. M

    Installing a post on a starter

    Your right, I will take it to a shop and have it done right. Thank you for your help. MasserD
  2. M

    Installing a post on a starter

    It is a new post that came in the kit.The old one is stripped, and also need new brushes. Thank You, MasserD
  3. M

    Installing a post on a starter

    I purchase a repair kit for a 9N starter. In the kit is a electric post that I need to install. Is there any instructions on removing the old and installing the new post on this site. I have rebuilt starters before but never installed a post. Are there anybody that can help me or where I can go...
  4. M

    Solder for the starter

    Thanks for your help. This is my first time rebuilding a starter, but I might get it right. Thanks Again,
  5. M

    Solder for the starter

    I have a 9N 6 volt starter that I am rebuilding and need to find out what kind of Solder do I use to solder the brushes? It has to be the right kind or it will not stay, I have heard. Thank You for your help. MasserD
  6. M

    Will this work on a 9N

    That is great, I am glad that I'm going in the right direction. I will rewire it and see if I can get it working. Thanks for your quick reply and I will get back with you on the results. Thank You, MasserD
  7. M

    Will this work on a 9N

    I have a front mount 1941 9N engine that I would like to change the wiring. I tried to wire my tractor to a 12 volt and I think I did it wrong. I was looking in the article section and the wiring diagram by Bob Melville for a Farm All Tractor. It looked like a simple wiring for changing to a 12...
  8. M

    Question on a wiring diagram in the articles

    I have a front mount 1941 9N engine that I would like to change the wiring. I tried to wire my tractor and I think I did it wrong. I was looking in the article section and the wiring diagram by Bob Melville for a Farm All Tractor. It looked like a simple wiring for changing to a 12 volt system...
  9. M

    9n Front mount Timing Problem

    Hello Friends, Its me again with a stupid question. I have tried timing my distributor on my 9n front mount. When I set the 1/4 on the wide side of the shaft and putting my finger on spark plug 1 hole to get TDC. But when I try to installed the distributor the shaft is backward and won't fit. I...
  10. M

    Front Mount Distributor Help

    Thanks for the information and fast reply. I will go out and try to put it back together the right way.
  11. M

    Front Mount Distributor Help

    I have a 9n and rebuilding the distribuior. I am having a problem starting and I have gone over many times and it still want start. While putting the distributor together I put the thin copper connector back on the connector on the big brass screw, is that where it goes? On page 19 fig fo44 of...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top