(800) 853-2651
SHOP NOW

Recent content by mmkid

Yesterday's Tractor Forums
  1. M

    Rear end fluid options

    I got weld on hubs , and my axle seals started leaking. Was wondering if anyone ran a thick grease in the rear end instead of 80/90 and had it stay pretty leak free ? Thanks
  2. M

    GTA parts wanted

    Hi I am looking for gta grill hood and gas tank perhaps call text with pictures and prices to James 906-226-2953
  3. M

    Lightweight cutting holes pattern

    I cut holes out in a pair and lost 13 pounds a wheel. Better bet would be to buy a pair of aluminum centers from Franklin degroff to fit your wheels
  4. M

    MM U swapping gears

    U pulling tractor , it has the 2-3-5 shift pattern. Would a third gear from a later u swap into where 1st gear is on this early u fairly easy ? Or go in any other slots ? Want to keep 3rd and 4th. I would be fine deleting 1,2, or 5.
  5. M

    Gear swap in an old U

    U pulling tractor , it has the 2-3-5 shift pattern. Would a third gear from a later u swap into where 1st gear is on this early u fairly easy ? Or go in any other slots ? Want to keep 3rd and 4th. I would be fine deleting 1,2, or 5.
  6. M

    MM UTS starter

    Jeff Gravert , (308) 940-0255 , sells a gear reduction starter for a situation like that
  7. M

    UB diesel

    There is a guy in Wisconsin with a 336 based diesel engine with a big square injector pump on the side and the injectors not in the stock holes but up higher in the head. Last weekend he went 8 mph in a 5000 class. Look up frannybadger on YouTube .
  8. M

    MM UTS starter

    What crankcase is used in this build ?
  9. M

    Electric water pump Davies Craig

    Has anyone ever used a Davies Craig booster electric water pump on there tractor. I bought it not realizing how small it is. Debating using it anyways. Thanks
  10. M

    4230 heads can I mill them

    Anyone mill down 4230 heads for more compression? Thanks
  11. M

    Minneapolis moline gb crank in a u

    Just bolt in the hole 403. Much easier.
  12. M

    M670 Minneapolis moline more rpm’s

    I go 27 or 28 hundred somewhere in there on a bone stock 403 with no valve float. I’m way too far away from any natpa pulls
  13. M

    M670 Minneapolis moline more rpm’s

    I can get 2000 with zip tied spring I want 2400 or so
  14. M

    M670 Minneapolis moline more rpm’s

    Hi. How can I get more rpm’s out of my m670. Have zip tied the spring and it didn’t get me as many as I want. Thanks
  15. M

    M670 more rpm’s

    Gas
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top