(800) 853-2651
SHOP NOW

Recent content by moline

Yesterday's Tractor Forums
  1. M

    Well, That wasn't a good way to start the day

    Dbernie where bouts are you from Chambana. I am about 25 miles north east.
  2. M

    head gasket

    Is the fire ring on the head gasket supposed to set on the sleeve flange?The head gasket in my kit does not come into the flange area.What keeps the sleeves in place if the fire ring is not on top of it?I have a 48 8N with the .040 sleeves.Thank you
  3. M

    GTB Propane

    My GTC had the dash you are describing from the factory(sqare box).But it also had the clamshell fenders.Could you have a dash from a GTC mounted on your GTB?
  4. M

    620 JD Lp

    Do you have the air filter cup on and filled with oil?It will not move the regulator diaphram if you dont.Fuel coming out of the middle hole?That is where the primer solenoid goes or am I misunderstanding?
  5. M

    60 LP

    Does it matter what the outside temp is?My 60LP will do that also if the temp is under40.It will fire and die.I jumped the resistor,Iprimed it until the oil gurgled in the air cleaner,set the fuel control(choke)all over the place-no go.It was suggested that maybe the starter was pulling so many...
  6. M

    Decals for M602

    I got mine from R & M distributors in Vail Iowa 712-677-2491.I was very happy with the quality and the appearance.
  7. M

    ampli torc

    Hi guys,thanks for the replies.It bugs me to hear noises like that.I just know that it is something being worn or damaged past repair.I dont think the torque is working,there is a very very slight decrease in speed.My M602 has a good drop in speed going into low and jumps right back up when put...
  8. M

    ampli torc

    I just bought a 4star from out of a weed patch.I have it running and it has a slight tap or knock from the amplitorc area.If you put it into low,the noise goes away.The tractor slows down very slightly when you put it into low.I loaded the driveline by applying the brakes and the torc does not...
  9. M

    60LP

    I have not tried to pull start it.If it started,that would point the finger at the batteries/cables/connections.I do have the bypass intact and I jumpered the resistor once just to make sure it was working.I made the cables out of 2/0(really fun to get it in the holders)all crimped connections...
  10. M

    60LP

    I have a 60LP that I refurbished.The tractor will not start below 35 Degrees.The engine will fire about twice and quit.It will do this all day or until the batteries are dead.The regulator is resealed,carb is resealed,air cleaner has fresh oil in it,new points ,plugs,cap,rotor,wires,battery...
  11. M

    M602 distributor #s

    Thanks for your research.No need to check rotation,but I appreciate the offer.Im still chasing some other options.Thanks again Moline
  12. M

    M602 distributor #s

    Well I looked again with my glasses off--you are correct.I read it wrong.I must not have been able to get it far enough from me to see it!I still run into the same problem.However on one site,they dont care about the number.They just want to know direction of rotation,# of cylinders,and voltage...
  13. M

    M602 distributor #s

    I was checking into an electronic ignition kit for my M602 on this site and others.I am not finding my distributor number.I found a 1112926 and a serial number on the breaker plate inside.No tags on the outside of the housing.I am finding numbers on both sides of mine listed.I thought a M670...
  14. M

    60LP Questions

    I just finished restoring a 60lp.It turned out great and is probably the sweetest running 2 cylinder I have.The head on that tractor is the same as a gas tractor.The pistons are higher compression.Mine was stuck and the cylinders were in bad shape;however,I could not find any oversize pistons.I...
  15. M

    IH 2504?? injection pump timing

    Hi,A friend of mine picked up an IH industrial tractor loader backhoe.The serial number plate has been sanded and I cant find the model.By the stamped serial number I think it is a 2504.It is a 4 cylinder indirect injected engine with a roosa master pump.The previous owner had removed the pump...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top